Abstract:Aluminium metal-matrix composites are broadly employed in industries like aerospace, marine, automobile-sector, and many others, generating a broad research interest. They are preferred for their high strength and low wear rate. This research work is mainly directed towards the fabrication of two types of metal-matrix composite materials using aluminium-alloy 6061(AA6061) as the matrix material and incorporating aluminium oxide (Al 2 O 3 ), aluminium nitride (AlN), and silicon carbide (SiC) as a reinforcement material. AA6061 has been reinforced with Al 2 O 3 and SiC particulates in AS series composites, while AA series composites, AA6061 has been reinforced with Al 2 O 3 and AlN particulates. This hybrid metal composite was constructed using the stir-casting method. These hybrid composites have been investigated for their physical and mechanical characteristics , viz. density, hardness, impact strength , void content, flexural strength, and tensile strength following the ASTM standards. Tribological characteristics of these hybrid composites were performed by Pin-on-disc (POD) tribometer. Taguchi's design of experimental technique was applied taking four factors viz. composition, sliding-velocity (SV), sliding-distance (SD), and load, and each having 4 levels. ANOVA was employed to find out meaningful parameters. SEM analysis of worn-surface was executed to find out the dominant wear mechanism. Experimental density was highest for AS42, and AA42 composites and void content were lowest for the same. Mechanical properties viz. density, hardness, impact strength, void content, flexural strength, and tensile strength were higher than the base alloy. From the response table of Taguchi analysis of AS and AA composite, the load factor significantly impacted the specific wear rate (SWR) to follow filler content (FC). It can be followed from the ANOVA table for AS composite that the load factor had a magnificent impact on the SWR. The SV and SD show no significant effect on SWR.

Multi-response optimisation of wear parameters of B4C reinforced Al-Fe-Si composites: Using Taguchi-grey relational analysis

Processing and Evaluation of Mechanical Properties and Dry Sliding Wear Behavior of AA6061-B4C Composites

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Analysis of Wear Behaviour of AA5052 Alloy Composites by Addition Alumina with Zirconium Dioxide Using the Taguchi-Grey Relational Method

Modeling of wear performance and surface roughness of AA6061-T6/B4C composite under dry sliding conditions by RSM

Study of Wear Behavior on AA6061 Reinforced with Hybrid Ceramic Composites through Optimization

Mechanical and Sliding Wear Performance of Vacuum-Cast AA7075-Co Alloy Composites: Parametric Optimization and Ranking Analysis

Evaluation of tribological parameters for boron carbide and graphite infused aluminium hybrid composite fabricated by stir casting technique

Mechanical and Sliding Wear Performance of AA356-Al2O3/SiC/Graphite Alloy Composite Materials: Parametric and Ranking Optimization Using Taguchi DOE and Hybrid AHP-GRA Method

Enhancing friction and wear performance in hybrid aluminum composites through grey relational analysis

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Optimization of process parameters of boron carbide filled Aluminium matrix composites using Grey Taguchi method

Optimization of Dry Sliding Wear in Hot-Pressed Al/B4C Metal Matrix Composites Using Taguchi Method and ANN

Multi Ceramic Particles Inclusion in the Aluminium Matrix and Wear Characterization through Experimental and Response Surface-Artificial Neural Networks

Wear rate optimization of tungsten carbide (WC) nano particles reinforced aluminum LM4 alloy composites using Taguchi techniques

Dry Sliding Wear Studies on Sillimanite and B4C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process

Development and Tribological Investigation of B4C Reinforced AA5082 Aluminum Alloy Cast Composites for Automotive Applications

Synergistic Effect of Ex Situ and In Situ Reinforcements on the Dry Reciprocating Wear Behavior of AA6061-B4C Composite Fabricated Using Varying K2TiF6 Flux Content

Evaluation of Wear Properties of Stir Cast AA7050 -10% B4C Ex Situ Composite through Fuzzy-TOPSIS MCDM Method

Multi Wear Response Optimization of Ti-6Al-7Nb Biomedical Alloy