Abstract:This study aims to examine the impact of agricultural waste materials—specifically silicon carbide (SiC) and palm sprout shell ash (PSSA)—on the mechanical properties, including density, porosity, tensile strength, compression strength, flexural strength, impact strength, and hardness, as well as the tribological behavior of Al-Cu-Mg alloy-based HRAMMCs. Parametric optimization was conducted on HRAMMCs to predict the effect of input constraints on the performance of the composite, considering the weight percentage of SiC, PSSA, and ultrasonic-assisted stirring time. Taguchi's L9 orthogonal array was used for the design of experiments (DOE), and the composites were fabricated accordingly. Their physical, mechanical, and tribological properties were determined experimentally. Taguchi-based Grey Relational Analysis for multi-optimization highlighted the potential of the HRAMMCs, with a density of 2.545 g/cm3, porosity of 5.810%, ultimate tensile strength of 341 MPa, flexural strength of 321 MPa, compressive strength of 394.016 MPa, Vickers hardness of 136.883 HV, wear rate of 6.88E-12 m3/m, and a coefficient of friction of 0.397. ANOVA shows that the developed mathematical model is a better fit for examining the impact of various factors on the GRG of and corresponding properties of developed HRAMMCs, Indicating the R2 value of the developed model is 99.33% (0.9933). The 2 wt.% SiC, 2 wt.% PSSA, and a stirring time of 7 minutes are optimal parameters for the present HRAMMCS; to reduce porosity, wear loss, and the coefficient of friction while increasing flexural strength, ultimate tensile strength, compressive strength, and Vickers microhardness. Moreover, the examination of the tensile and impact fracture surfaces and worn surfaces was carried out using SEM analysis of the alloy and composite produced under the optimal experimental conditions. The results of the fracture surface analysis indicated that the failure of both tensile and impact fractures was due to a amalgamation of ductile and brittle behaviors. The composites exhibited lower ductility than that of the base alloys. A study of the wear mechanism revealed that it was a mixture of adhesive and abrasive wear mechanisms. The SiC and PSSA ceramic reinforcements demonstrate higher hardness compared to the alloy, which restricts the fluid-like movement of the matrix. When these reinforcements were added to the alloy, they substantially decreased the occurrence of severe delamination and the formation of adhesive wear particles.

Enhancing friction and wear performance in hybrid aluminum composites through grey relational analysis

Mechanical and Sliding Wear Performance of AA356-Al2O3/SiC/Graphite Alloy Composite Materials: Parametric and Ranking Optimization Using Taguchi DOE and Hybrid AHP-GRA Method

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

A combined approach to grey relational analysis and principal component analysis for development of input parameters in the wear characterization of Al7075 (SiC+Al2O3) hybrid metal matrix composites

Influence of wear parameters on friction performance of A356 aluminum – graphite/ granite particles reinforced metal matrix hybrid composites

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Parametric Optimization and Ranking Analysis of Hybrid AA2024–SiC/Si3N4 Alloy Composites Based on Mechanical and Sliding Wear Performance

Multi-response optimisation of wear parameters of B4C reinforced Al-Fe-Si composites: Using Taguchi-grey relational analysis

Characterization, mechanical properties, and wear behavior of functionally graded aluminum hybrid composite

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Evaluation of tribological parameters for boron carbide and graphite infused aluminium hybrid composite fabricated by stir casting technique

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

Analysis of Wear Behaviour of AA5052 Alloy Composites by Addition Alumina with Zirconium Dioxide Using the Taguchi-Grey Relational Method

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

Study of Wear Behavior on AA6061 Reinforced with Hybrid Ceramic Composites through Optimization

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Taguchi-based Grey Relational Analysis for multi-response optimization of the characteristics of HRAMMCs reinforced with agro-waste and SIC produced by ultrasonic-assisted bottom pour two-stage stir casting

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

High speed machining and optimisation of Al/SiC/Gr hybrid metal matrix composites using ANOVA and grey relational analysis

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Dry sliding wear characteristics of hybrid aluminum alloy with nano-fly ash and nano-yttrium oxide