Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Aluminum alloys feature impressive levels of strength, ductility, castability, wear resistance, and corrosion resistance, making them highly advantageous for the aviation and automotive industries. This study investigates the dry wear performance of hybrid nanocomposites (HNCs) produced using Al6061 as the matrix, with nano-fly ash (FA) and nano-yttrium oxide (Y2O3) as reinforcing agents, utilizing the stir-casting method. The weight percentage (wt-%) of FA was fixed at 4 wt-%, while the Y2O3 varied from 1 wt-% to 3 wt-%. The specimens were prepared following ASTM-G99 standards and tested using a pin-on-disc apparatus with an E31 steel disc under four different loads: 10 N, 20 N, 30 N, and 40 N. It has been observed that wear rate has been increased with the increase in the applied load. The maximum wear rate has been recorded for the base Al6061 alloy as 5.63 × 10−4 mm3/N-m at 40 N load due to its lower wear resistance and less hardness value. The addition of reinforcement particles in the base alloy results in the grain refinement and improvement in the load-bearing capacity. It has been found that at 40 N load, the Al-6061 alloy reinforced with (4 wt-% FA + 3 wt-% Y2O3) is 56.83% superior in terms of wear resistance (2.43 × 10−4 mm3/N-m) as compared to Al6061 base alloy. The hybrid nano-composite containing 4 wt-% FA + 3 wt-% Y2O3 showed the highest value of microhardness as 123.2 HV, which is 136% higher than that of base alloy due to the higher load-bearing characteristics of the reinforcement particles. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) have been employed to analyze both unworn and worn surfaces, revealing uniform dispersion of reinforcement particles, the formation of an oxide layer, micro-pitting, wear debris, and material delamination. Grain refinement has been examined using the line intercept method (ASTM E1382-97), and X-ray diffraction (XRD) confirmed the elemental composition of the nano-reinforcements.

Synergistic approach to tribological characterization of hybrid aluminum metal matrix composites with ZrB2 and fly ash: Experimental and predictive insights

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Prediction of tribological performance of AA8011/wt.%ZrO2 based composites fabricated by stir casting route

Experimental Investigation of the Influence of Various Wear Parameters on the Tribological Characteristics of AZ91 Hybrid Composites and Their Machine Learning Modeling

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Prediction of frictional behaviour through regression equations: A statistical modelling approach validated with machine learning

Investigation of the Wear Behavior of AA6063/Zirconium Oxide Nanocomposites Using Hybrid Machine Learning Algorithms

Optimized machine learning with hyperparameter tuning and response surface methodology for predicting tribological performance in bio‐composite materials

Studies on tribological behavior of aluminum hybrid composites strengthened with MoS2 and wheat husk ash

Enhancing mechanical and tribological performance of hybrid composites: An experimental study utilizing response surface methodology and firefly algorithm

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

A Review on the Significance of Hybrid Particulate Reinforcements on the Mechanical and Tribological Properties of Stir-Casted Aluminum Metal Matrix Composites

Optimization and fuzzy model for evaluation of mechanical and tribological properties of Al-CNT-Si3N4 based nano and hybrid composites

Synergistic approach to wear rate forecasting in AZ31/5% Yttria stabilized zirconia reinforced composite through response surface methodology-genetic algorithm integration

Effect of Graphite Addition on Mechanical Properties and Elevated Temperature Tribological Behaviour of Aluminium Zinc Alloy

Optimization of Tribological Behaviour of Ti6Al4V/TiB2/TiC Hybrid MMCs Using Response Surface Methodology

Tribological analysis of titanium alloy (Ti-6Al-4V) hybrid metal matrix composite through the use of Taguchi’s method and machine learning classifiers

Dry sliding wear behaviour of AA6082/BN/Mos2 hybrid metal matrix composites synthesized using stir casting process

Dry sliding wear characteristics of hybrid aluminum alloy with nano-fly ash and nano-yttrium oxide

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Enhancing friction and wear performance in hybrid aluminum composites through grey relational analysis