Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

A Study on Mechanical and Tribological Properties of Aluminum 7075 MMCS Reinforced with Silicon Carbide and Coconut Husk by Powder Metallurgy Process

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Investigation of Tribological Behavior of a Novel Hybrid Composite Prepared with Al-Coconut Shell Ash Mixed with Graphite

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Studies on tribological behavior of aluminum hybrid composites strengthened with MoS2 and wheat husk ash

PHYSICO-TRIBOLOGICAL ANND WEAR MECHANISM CHARACTERISTICS OF HYBRID REINFFORCED Al6063 MATRIX COMPOSITES

Mechanical Behaviour of Aluminium Hybrid Composites Reinforced with: Rice Husk Ash - Silicon Carbide - Copper Nanoparticles

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Effect of forging on mechanical properties of rice husk ash-silicon carbide reinforced Al1100 hybrid composites

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

STUDY OF MECHANICAL PROPERTIES AND WEAR BEHAVIOR OF ALUMINUM MATRIX COMPOSITES REINFORCED WITH SILICON CARBIDE PARTICLES

The utilisation of coconut shell ash in production of hybrid composite: Microstructural characterisation and performance analysis