Abstract:Personal thermal management (PTM) materials have recently received considerable attention to improve human body thermal comfort with potentially reduced energy consumption. Strategies include passive radiative cooling and warming. However, challenges remain for passive thermal regulation of one material or structure in both harsh hot and cold environments. In this work, silica aerogels derived from sodium silicate were prepared through a solvent-boiling strategy, where hydrophobization, solvent exchange, sodium purification, and ambient pressure drying (HSSA) proceeded successively and spontaneously in a one-pot process. This strategy leads to the synthesis of superhydrophobic silica aerogels with extremely low energy consumption without out the use of an ion-exchange resin or low surface tension solvents. Silica aerogels possess a high specific surface area (635 m<sup>2</sup>/g), high contact angle (153°), and low thermal conductivity (0.049 W/m K). A layer-by-layer (LBL) structure including the silica aerogel layer and an extra phase change material layer was designed. The structure demonstrates dual-functional thermal regulation performance in both harsh cold (-30 °C) and hot (70 °C) environments, where the time to reach equilibrium is postponed, and the inner temperature of the LBL structure can be kept above 20 °C in harsh cold environments (-30 °C) and below 31 °C in harsh hot environments (70 °C). A proof-of-concept experimental setup to simulate the illumination of sunlight also proved that the inside temperature of a model car protected by the LBL structure was below 28 °C, while the outside temperature was 70 °C. In addition, these results are well supported by theoretical COMSOL simulation results. The findings of this work not only provide an eco-friendly approach to synthesize silica aerogels but also demonstrate that the LBL structure is a robust dual-functional PTM system for thermal regulation in both harsh hot and cold environments.

In-Situ Synthesis of Layered Double Hydroxide/Silica Aerogel Composite and Its Thermal Safety Characteristics

Enhancing thermal safety of hydrophobic silica aerogels by incorporating sodium dodecyl sulfate intercalated layered double hydroxides

Insights into the Thermal Safety of Ambient Pressure Dried Hydrophobic Montmorillonite/silica Aerogel Composites

Surface chemistry, skeleton structure and thermal safety of methylsilyl modified silica aerogels by heat treatment in an argon atmosphere

Improving the flame retardance of hydrophobic silica aerogels through a facile post-doping of magnesium hydroxide

Reducing the thermal hazard of hydrophobic silica aerogels by using dimethyldichlorosilane as modifier

Alumina-Doped Silica Aerogels for High-Temperature Thermal Insulation

Rapid Synthesis of Super Insulation Silica Aerogel Composites Strengthened with Mullite Fibers

Regulating the hydrophobicity and pore structure of silica aerogel for thermal insulation under humid and high temperature conditions

Tuning Thermal Stability and Fire Hazards of Hydrophobic Silica Aerogels Via Doping Reduced Graphene Oxide

Flammability and Oxidation Kinetics of Hydrophobic Silica Aerogels.

Superhydrophobic Silica Aerogels and Their Layer-by-Layer Structure for Thermal Management in Harsh Cold and Hot Environments

Synthesis and Characterization of Silica Aerogel and Its Composite Materials

Experimental Investigation of the Combustion Characteristics and Thermal Hazards of Methylsilyl-Modified Silica Aerogels

Novel silica-modified boehmite aerogels and fiber-reinforced insulation composites with ultra-high thermal stability and low thermal conductivity

Synthesis of a novel Al 2 O 3 –SiO 2 composite aerogel with high specific surface area at elevated temperatures using inexpensive inorganic salt of aluminum

Enhanced Flame Retardancy of Hydrophobic Silica Aerogels by Using Sodium Silicate As Precursor and Phosphoric Acid As Catalyst

Novel Al2O3–SiO2 composite aerogels with high specific surface area at elevated temperatures with different alumina/silica molar ratios prepared by a non-alkoxide sol–gel method

Preparation of High-Temperature Resistant Aerogels by Incorporating Aluminum Sol into Composite Silica Sources Using Ambient Pressure Drying

Synthesis of hydrophobic silica aerogel and its composite using functional precursor