Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

Performance and wear mechanism of spark plasma sintered WC-Based ultrafine cemented carbides tools in dry turning of Ti–6Al–4V

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Investigation on the Performance of Spark Plasma Sintered Ultrafine WC-Co Cemented Carbide End Mills During High-Speed Precision Milling of Ti-6Al-4V Alloy

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

Cutting performance and wear mechanism of spark plasma–sintered silicon nitride ceramics tool in dry turning of 41Cr4 hardened steel

Preparation, properties and microstructure of high hardness WC-co cemented carbide tool materials for ultra-precision machining

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

Performance and wear mechanisms of coated PCBN tools in high-speed turning superalloy GH4202

Ultrafine WC–Co cemented carbide end mills prepared by spark plasma sintering and wear mechanism in milling of AISI H13

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

Tool Life and Wear Mechanism of WC–5TiC–0.5VC–8Co Cemented Carbides Inserts when Machining HT250 Gray Cast Iron

Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning

Effects of nano-alumina on mechanical properties and wear resistance of WC-8Co cemented carbide by spark plasma sintering

A comparative study on tool life and wear of uncoated and coated cutting tools in turning of tungsten heavy alloys

Tool wear in laser ultrasonically combined turning of tungsten carbide with PCD tools

Wear Mechanisms and Notch Formation of Whisker-Reinforced Alumina and Sialon Ceramic Tools during High-Speed Turning of Inconel 718

Spark Plasma Sintering Preparation of Tungsten Carbide-Reinforced Iron-Based Composite Materials: Wear Resistance Performance and Mechanism

Wear‐Resistant Titanium Carbonitride Coatings Onto WC–Co Cutting Tools by Pulsed High‐Energy Density Plasma