Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

A comparative study on tool life and wear of uncoated and coated cutting tools in turning of tungsten heavy alloys

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Performance and wear mechanisms of coated PCBN tools in high-speed turning superalloy GH4202

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

Finite element analysis of Ti 1-x Al x N coated tools cutting performance and tool wear during Ti-6Al-4V milling

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings

Durability of cutting tools with deposited ceramic–metallic coatings (Ti,Al)N – Cu and (Ti,Al)N – Ni when turning and milling steels

Wear characteristics and performance in side milling of Ti 2 AlNb intermetallic alloys with coated and uncoated end mills

Wear behavior of different coated tools in MQL-assisted high-speed milling of magnesium-based rare-earth alloys

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Optimization of flank wear and surface quality in the turning of 1.2343 tool steel using carbide tools coated via different methods

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Alloy Coated Cutting Tool Wear Characteristics Experimental Study in Fine Boring

Cutting Performance and Tool Wear of AlCrN- and TiAlN-Coated Carbide Tools during Milling of Tantalum–Tungsten Alloy

Effect of Al Content on the Wear Evolution of Ti1-xAlxN-Coated Tools Milling Ti-6Al-4V Alloy

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Study on the Wear Mechanism and Tool Life of Coated Gun Drill

Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools