Abstract:Titanium alloys Ti-6Al-4V are widely used in many industrial and medical applications because of their superior qualities over many other alloys like aluminum and steel. Some of their properties like high strength to weight ratio, ability to maintain strength at elevated temperatures (around 500°C) and ability of corrosion resistance in severe environmental conditions has made them excellent to use in many aerospace and bio-medical industrial applications. But the properties which make them ideal for most practical applications severely hinders their machinability and therefore, the material is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures and due to which these alloys are still machined with un-coated carbide tools at very low cutting speeds and the advantage of machining at high speed machining regime for these alloys are still not seen. The high cost of super hard cutting tools and also possible chemical reaction with work material still does not allow industrialists to use these materials for machining of titanium alloy. On the other hand recent advances in deposition of coating material on carbide tools has attracted many researchers in finding their advantages and best optimal coating combination for enhancing machinability of titanium alloys with carbide tools. This study therefore is specifically aimed and designed in evaluating the effectiveness of different coating layers on k-grade cemented carbide cutting tool by studying their effect on cutting forces, tool stresses and heat distribution by using finite element numerical simulations at high speed cutting conditions. Finite element numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Three different type of coating materials has been used in this study and the results has shown that the k-grade cemented carbide cutting tool with multi-layer coating (Al2O3+TiAlN+TiN) has shown some advantages over uncoated and single layer coating (TiAlN) in terms of heat distribution, cutting forces and tool stresses at same cutting conditions due to higher hot strength and resistance to adhesion. It can be concluded from the study that multi-layer coated k-grade cemented carbide cutting tools can be used at slightly higher speeds than un-coated or single layer coated carbide tools and can give higher tool life as compared to single layer and un- coated carbide tools.

Investigation on the Performance of Spark Plasma Sintered Ultrafine WC-Co Cemented Carbide End Mills During High-Speed Precision Milling of Ti-6Al-4V Alloy

Ultrafine WC–Co cemented carbide end mills prepared by spark plasma sintering and wear mechanism in milling of AISI H13

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Performance and wear mechanism of spark plasma sintered WC-Based ultrafine cemented carbides tools in dry turning of Ti–6Al–4V

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools

Cutting performance and surface quality of Ti-6Al-4V by longitudinal ultrasonic vibration-assisted high-speed dry milling with coated carbide tools

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Wear characteristics and performance in side milling of Ti 2 AlNb intermetallic alloys with coated and uncoated end mills

Microstructure and Mechanical Properties of Spark Plasma Sintered Si3N4/WC Ceramic Tools

Microstructure, mechanical property and cutting performance of (Ti,W)C/Mo/Co/Ni cermet tool material prepared by spark plasma sintering and high frequency induction heating

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Evaluating the Effectiveness of Various Coating Layers Applied on K-Grade Cemented Carbide Cutting Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling

Wear of End Mills with Carbon Coatings When Aluminum Alloy A97075 High-Speed Processing

Finite element analysis of Ti 1-x Al x N coated tools cutting performance and tool wear during Ti-6Al-4V milling

An Investigation of Cutting Performance and Action Mechanism in Ultrasonic Vibration-Assisted Milling of Ti6Al4V Using a PCD Tool

Spark Plasma Sintering Preparation of Tungsten Carbide-Reinforced Iron-Based Composite Materials: Wear Resistance Performance and Mechanism