A Low-Intensity Pulsed Ultrasound Interface ASIC for Wearable Medical Therapeutic Device Applications

Xuanjie Ye,Xiaoxue Jiang,Shuren Wang,Jie Chen
DOI: https://doi.org/10.3390/electronics13061154
IF: 2.9
2024-03-21
Electronics
Abstract:Low-intensity pulsed ultrasound (LIPUS) is a non-invasive medical therapy that has attracted recent research interest due to its therapeutic effects. However, most LIPUS driver systems currently available are large and expensive. We have proposed a LIPUS interface application-specific integrated circuit (ASIC) for use in wearable medical devices to address some of the challenges related to the size and cost of the current technologies. The proposed ASIC is a highly integrated system, incorporating a DCDC module based on a charge pump architecture, a high voltage level shifter, a half-bridge driver, a voltage-controlled oscillator, and a corresponding digital circuit module. Consequently, the functional realization of this ASIC as a LIPUS driver system requires only a few passive components. Experimental tests indicated that the chip is capable of an output of 184.2 mW or 107.2 mW with a power supply of 5 V or 3.7 V, respectively, and its power conversion efficiency is approximately 30%. This power output capacity allows the LIPUS driver system to deliver a spatial average temporal average (SATA) of 29.5 mW/cm2 or 51.6 mW/cm2 with a power supply of 3.7 V or 5 V, respectively. The total die area, including pads, is 4 mm2. The ASIC does not require inductors, improving its magnetic resonance imaging (MRI) compatibility. In summary, the proposed LIPUS interface chip presents a promising solution for the development of MRI-compatible and cost-effective wearable medical therapy devices.
engineering, electrical & electronic,computer science, information systems,physics, applied
What problem does this paper attempt to address?
The main problem that this paper attempts to solve is the large size and high cost of existing low - intensity pulsed ultrasound (LIPUS) driving systems. Specifically, the author proposes an application - specific integrated circuit (ASIC) for the LIPUS interface of wearable medical devices, aiming to reduce the size and cost of the system through a highly integrated design while improving its compatibility in the MRI environment. ### Background and Objectives of the Paper - **Background**: As a non - invasive medical therapy, low - intensity pulsed ultrasound (LIPUS) has attracted the attention of researchers in recent years due to its therapeutic effects. However, existing LIPUS driving systems are usually large in size and expensive. - **Objective**: To develop a miniaturized LIPUS - interface ASIC chip for creating a wearable ultrasonic treatment system to address the challenges of existing technologies in terms of size and cost. ### Main Contributions 1. **Highly Integrated Design**: The proposed ASIC chip integrates multiple functional modules, including a DC - DC module based on a charge - pump architecture, a high - voltage level shifter, a half - bridge driver, a voltage - controlled oscillator, and corresponding digital circuit modules. 2. **Miniaturization**: The area of the entire chip is only 4 square millimeters, including pads. 3. **High Efficiency**: Experimental tests show that the chip can output 184.2 mW and 107.2 mW of power under 5V and 3.7V power supplies respectively, with a conversion efficiency of about 30%. 4. **MRI Compatibility**: Since no inductor is used, this ASIC chip has good MRI compatibility and is suitable for MRI - guided ultrasound treatment procedures. ### Technical Details - **Charge - Pump Design**: A four - stage charge - pump design is adopted, which can boost the portable power supply voltage (3.7V to 5V) to a level sufficient to drive the ultrasonic transducer (about 12V to 20V). The operating frequency of the charge - pump can be adjusted by a voltage - controlled oscillator (VCO) to adapt to different load conditions. - **High - Voltage Level Shifter (HVLS)**: It is used to drive the high - side NMOS transistor in the half - bridge driver to ensure its normal operation at high voltages. - **Half - Bridge Driver**: Composed of two high - voltage NMOS transistors, it is used to drive the ultrasonic transducer. In the design, a bootstrap circuit and a high - voltage level shifter are used to boost the gate voltage of the high - side NMOS. - **Voltage - Controlled Oscillator (VCO)**: It generates a clock signal with an adjustable frequency to control the operating frequency of the charge - pump, thereby optimizing the output power and efficiency. ### Experimental Results - **Performance Evaluation**: The performance of the ASIC chip was verified through simulation and actual tests. The results show that the chip can output 107.2 mW and 184.2 mW of power under 3.7V and 5V power supplies respectively, with conversion efficiencies of 30.8% and 29.7% respectively. - **Ultrasonic Output**: Under 3.7V and 5V power supplies, the ultrasonic output powers are 28 mW and 49 mW respectively, and the corresponding mean spatial - temporal - average (SATA) intensities are 29.5 mW/cm² and 51.6 mW/cm² respectively. ### Conclusions - **Application Prospects**: The proposed LIPUS - interface ASIC chip provides a feasible solution for developing miniaturized, low - cost, and MRI - compatible wearable medical treatment devices. - **Future Research Directions**: Further optimize the MRI compatibility of the system, explore the MRI compatibility of other modules, and improve the design of peripheral circuits. In conclusion, this paper successfully solves the challenges of existing LIPUS driving systems in terms of size and cost by proposing a highly integrated LIPUS - interface ASIC chip, providing a new technological path for the development of wearable medical devices.