Abstract:Utilizing injectable devices for monitoring animal health offers several advantages over traditional wearable devices, including improved signal-to-noise ratio (SNR) and enhanced immunity to motion artifacts. We present a wireless application-specific integrated circuit (ASIC) for injectable devices. The ASIC has multiple physiological sensing modalities including body temperature monitoring, electrocardiography (ECG), and photoplethysmography (PPG). The ASIC fabricated using the CMOS 180 nm process is sized to fit into an injectable microchip implant. The ASIC features a low-power design, drawing an average DC power of 155.3 µW, enabling the ASIC to be wirelessly powered through an inductive link. To capture the ECG signal, we designed the ECG analog frontend (AFE) with 0.3 Hz low cut-off frequency and 45-79 dB adjustable midband gain. To measure PPG, we employ an energy-efficient and safe switched-capacitor-based (SC) light emitting diode (LED) driver to illuminate an LED with milliampere-level current pulses. A SC integrator-based AFE converts the current of photodiode with a programmable transimpedance gain. A resistor-based Wheatstone Bridge (WhB) temperature sensor followed by an instrumentation amplifier (IA) provides 27–47 °C sensing range with 0.02 °C inaccuracy. Recorded physiological signals are sequentially sampled and quantized by a 10-bit analog-to-digital converter (ADC) with the successive approximation register (SAR) architecture. The SAR ADC features an energy-efficient switching scheme and achieves a 57.5 dB signal-to-noise-and-distortion ratio (SNDR) within 1 kHz bandwidth. Then, a back data telemetry transmits the baseband data via a backscatter scheme with intermediate-frequency assistance. The ASIC’s overall functionality and performance has been evaluated through an in vivo experiment.

A 1.0 V 78 μw Reconfigurable ASIC Embedded in an Intelligent Electrode for Continuous Remote ECG Applications

An ASIC Solution for Intelligent Electrodes and Active-Cable Used in a Wearable ECG Monitoring System.

A Multi-Parameter Bio-Electric ASIC Sensor with Integrated 2-Wire Data Transmission Protocol for Wearable Healthcare System

Intelligent electrode design for long-term ECG monitoring at home: Prototype design using FPAA and FPGA

Design of a self-organized Intelligent Electrode for synchronous measurement of multiple bio-signals in a wearable healthcare monitoring system

An Active-Cable Connected ECG Monitoring System for Ubiquitous Healthcare

Bio-chip ASIC and Printed Flexible Cable on Paper Substrate for Wearable Healthcare Applications

A Miniature On-Chip Multi-Functional ECG Signal Processor with 30 &#x00b5;w Ultra-Low Power Consumption

A 58 nW ECG ASIC With Motion-Tolerant Heartbeat Timing Extraction for Wearable Cardiovascular Monitoring

A Novel Wearable ECG Monitoring System Based on Active-Cable and Intelligent Electrodes

A 2.63 μW ECG Processor With Adaptive Arrhythmia Detection and Data Compression for Implantable Cardiac Monitoring Device

An ECG-on-Chip for Wearable Cardiac Monitoring Devices

A 1.92 Μa Always-on ECG Monitoring Mixed-Signal SoC for Implantable Medical Application.

An Ultra-Low Power ECG Acquisition and Monitoring ASIC System for WBAN Applications

A 746 Nw ECG Processor ASIC Based on Ternary Neural Network

A Wireless 8-Channel ECG Biopotential Acquisition System for Dry Electrodes

A Wireless Miniature Injectable Device with Memory-Assisted Backscatter for Multimodal Animal Physiological Monitoring

A low power configurable bio-impedance spectroscopy (BIS) ASIC with simultaneous ECG and respiration recording functionality.

An ASIC Design of Multi-Electrode Digital Basket Catheter Systems with Reconfigurable Compressed Sampling.

A Low-Power Portable ECG Sensor Interface with Dry Electrodes

A Wireless Multimodal Physiological Monitoring ASIC for Animal Health Monitoring Injectable Devices

A 1.0 V 78 &#x03bc;w Reconfigurable ASIC Embedded in an Intelligent Electrode for Continuous Remote ECG Applications