Abstract:This article presents an application-specific integrated circuit (ASIC) for catheter-based 3-D ultrasound imaging probes. The pitch-matched design implements a comprehensive architecture with high-voltage (HV) transmitters, analog front ends, hybrid beamforming analog-to-digital converters (ADCs), and data transmission to the imaging system. To reduce the number of cables in the catheter while maintaining a small footprint per element, transmission (TX) beamforming is realized on the chip with a combination of a shift register (SR) and a row/column (R/C) approach. To explore an additional cable-count reduction in the receiver part of the design, a channel with a combination of time-division multiplexing (TDM), subarray beamforming, and multi-level pulse amplitude modulation (PAM) data transmission is also included. This achieves an 18-fold cable-count reduction and minimizes the power consumption in the catheter by a load modulation (LM) cable driver. It is further explored how common-mode interference can limit beamforming gain and a strategy to reduce its impact with local regulators is discussed. The chip was fabricated in TSMC 0.18- $\mu$ m HV BCD technology and a 2-D PZT transducer matrix of 16 $\times$ 18 elements with a pitch of 160 $\mu$ m and a center frequency of 6 MHz was manufactured on the chip. The system can generate all required TX patterns at up to 30 V, provides quick settling after the TX phase, and has an reception (RX) power consumption of only 1.12 mW/element. The functionality and operation of up to 1000 volumes/s have been demonstrated in electrical and acoustic imaging experiments.

An ASIC Design of Multi-Electrode Digital Basket Catheter Systems with Reconfigurable Compressed Sampling.

An ASIC Solution for Intelligent Electrodes and Active-Cable Used in a Wearable ECG Monitoring System.

A 1.0 V 78 μw Reconfigurable ASIC Embedded in an Intelligent Electrode for Continuous Remote ECG Applications

A Multi-Parameter Bio-Electric ASIC Sensor with Integrated 2-Wire Data Transmission Protocol for Wearable Healthcare System

Design of a self-organized Intelligent Electrode for synchronous measurement of multiple bio-signals in a wearable healthcare monitoring system

Bio-chip ASIC and Printed Flexible Cable on Paper Substrate for Wearable Healthcare Applications

Intelligent electrode design for long-term ECG monitoring at home: Prototype design using FPAA and FPGA

A Highly Adaptive Lossless ECG Compression ASIC for Wireless Sensors Based on Hybrid Gomlomb Coding.

A 2.63 μW ECG Processor With Adaptive Arrhythmia Detection and Data Compression for Implantable Cardiac Monitoring Device

A Front-End ASIC with High-Voltage Transmit Switching and Receive Digitization for 3-D Forward-Looking Intravascular Ultrasound Imaging.

A 0.18-&Amp;#x003bc;m CMOS Multirate Filter Bank Asic for Biomedical Applications

A Pitch-Matched High-Frame-Rate Ultrasound Imaging ASIC for Catheter-Based 3-D Probes

An AFE for Catheter-Based IEGM Sensing with Inverter-based SAR ADC

Digital-analog Mixed-Mode Baseband Processing ASIC for Wireless Endoscopic Systems

An Energy-Efficient Design for ECG Recording and R-Peak Detection Based on Wavelet Transform

A Miniature On-Chip Multi-Functional ECG Signal Processor with 30 &#x00b5;w Ultra-Low Power Consumption

Reconfigurable Architecture for Multi-lead ECG Signal Compression with High-frequency Noise Reduction

A Pitch-Matched Front-End ASIC with Integrated Subarray Beamforming ADC for Miniature 3-D Ultrasound Probes

An ECG-on-Chip for Wearable Cardiac Monitoring Devices

Signal Processing System-on-chip Design for Biomedical Applications.

A Front-End ASIC for Miniature 3-D Ultrasound Probes with In-Probe Receive Digitization