Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673o K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673o K.

Tearing Resistance of AA7075-T6 Sheet at 25 °C and 180 to 200 °C

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Study on High-Temperature Mechanical Properties and Forming Limit Diagram of 7075 Aluminum Alloy Sheet in Hot Stamping

Formability Evaluation of Aluminum Alloy 6061-T6 Sheet at Room and Elevated Temperatures

Tensile Behavior and Microstructure Evolution of an Extruded 6082 Aluminum Alloy Sheet at High Temperatures

Experimental and numerical studies on mechanical properties of hot-stamped tailor welded AA7075-T6

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Optimum heating time for warm forming of AA7075 aluminum alloy in T6 condition

High-Temperature Tensile Mechanical Properties and Microstructure of Rolled 6082-T6 Aluminum Alloy Sheets

Evolution of microstructure and properties of AA 7072/7075/7072 composite sheets during various finish rolling temperature

Intermediate temperature tensile behavior and processing map of a spray formed 7075 aluminum alloy

Experimental study on cold forming process of 7075 aluminum alloy in W temper

Local and global tensile deformation behavior of AA7075 sheet material at 673oK and different strain rates

Enhanced formability and accelerated precipitation behavior of 7075 Al alloy extruded rod by high temperature aging

Effects of aging temperature on microstructure and high cycle fatigue performance of 7075 aluminum alloy

Effect of Heat Treatment Conditions on Mechanical Properties and Precipitates in Sheet Metal Hot Stamping of 7075 Aluminum Alloy

Hot Deformation Behavior of Aluminum Alloys AA7010 and AA7075

Deformation Behavior and Mechanical Properties of AA7075 During Pre-hardened Aluminum Alloy Hot Forming Process

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

Microstructure and Properties Evolution of 7075 Al alloy in Hot Rolling and Short Process Heat Treatment

Edge-crack free and high mechanical properties of AA7075 sheets by using cryorolling and subsequent aging