Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673 degrees K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673 degrees K.

Formability Evaluation of Aluminum Alloy 6061-T6 Sheet at Room and Elevated Temperatures

Investigation of formability of aluminum alloy sheet at elevated temperature

Experimental Investigation of Forming Limit Curves and Deformation Features in Warm Forming of an Aluminium Alloy

Investigation on Yield Behavior of 7075-T6 Aluminum Alloy at Elevated Temperatures

Experimental Study on the Forming Limit Diagrams (FLD) of 7075-T6 Aluminum Alloy Sheet at Warm State

Tensile Deformation Behavior of 5A90 Al-Li Alloy Sheet at Elevated Temperature

Investigation on the Formability of 5A06 Sheet for Rapid Gas Forming

An Experimental Investigation on the Deformation and Post-Formed Strength of Heat-Treatable Aluminium Alloys Using Different Elevated Temperature Forming Processes

An Experimental and Numerical Investigation on the Formability of AA7075 Sheet in Hot Stamping Condition

Study on High-Temperature Mechanical Properties and Forming Limit Diagram of 7075 Aluminum Alloy Sheet in Hot Stamping

Forming Limits of Magnesium Alloy AZ31B Sheet at Elevated Temperatures

Numerical Investigation for Formability of Aluminum 6016 Alloy under Non-Isothermal Warm Forming Process

On the Thermal Forming Limit Diagram (TFLD) with GTN Mesoscopic Damage Model for AA7075 Aluminum Alloy: Numerical and Experimental Investigation

Research on the Constitutive Relationship of 5A90 Aluminum-lithium Alloy at Hot Forming Temperature

Analysis of hot Formability of Al-4.6Mg-0.6Mn Alloy (AA5083)

Thermal Deformation Behavior and Processing Maps of 7075 Aluminum Alloy Sheet Based on Isothermal Uniaxial Tensile Tests

Local and global tensile deformation behavior of AA7075 sheet material at 673K and different strain rates

Strain Rate and Temperature Effects on Formability and Microstructure of AZ31B Magnesium Alloy Sheet

Development of the Forming Limit Diagram for AA6016-T4 at Room Temperature Using Uniaxial Tension of Notched Samples and a Biaxial Test

Constitutive equations of high strength aluminum alloy sheet 7B04-T6 under warm tension

An Experimental Investigation into the Formability of Hydroforming 5A02 Al-tubes at Elevated Temperature