Abstract:Currently, the hot forming of aluminum alloys has garnered significant attention for overcoming poor formability at room temperature (RT). However, the current hot forming technique is facing problems such as time-consuming procedures and high economic cost. To improve forming efficiency, we herein propose a novel forming technique for heat-treatable aluminum alloys, termed pre-aged hardening warm forming (PHF) process. An Al–Zn–Mg–Cu alloy is used to investigate the flow behavior, drawing formability, and post-forming mechanical properties during the aforementioned process. Uniaxial tensile tests and Erichsen tests are conducted to evaluate the plastic flow behavior and drawability, respectively. Stamping tests are performed on a cap beam component to verify the engineering feasibility of the forming technique. Optical microscopy (OM) and transmission electron microscopy (TEM) are performed to characterize the microstructure evolution during the PHF process. The tensile test results show that the pre-aged alloys exhibit true fracture elongation similar to the fracture elongation of the O-temper alloy at RT, and that the Erichsen values of the pre-aged alloys are 5%–16% higher than that of the O-temper alloy at 200 °C. The results of the stamping tests for the cap beam component indicate that the optimal final strength of the stamped component achieves σ/σ0.2 = 566 MPa/500 MPa, exceeding the strength of the AA7075-T6 alloy. OM observations show that the stamping process does not significantly affect the grain sizes of the pre-aged alloys. TEM results show that numerous thermostable GPⅡ zones exist in the pre-aged alloys, and that the stamping procedure transforms the GPⅡ zones to dispersed η′ phases and results in the entanglement of numerous dislocations. The dual effects of phase transformation and plastic deformation during the PHF process contribute to the desirable mechanical properties of the stamped components.

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

Study on High-Temperature Mechanical Properties and Forming Limit Diagram of 7075 Aluminum Alloy Sheet in Hot Stamping

Effect of Heat Treatment Conditions on Mechanical Properties and Precipitates in Sheet Metal Hot Stamping of 7075 Aluminum Alloy

Experimental study on cold forming process of 7075 aluminum alloy in W temper

Hot deformation characteristics and processing maps of AA7075-H18 alloy sheet under hot forming process conditions

Application of Combined W-Temper and Cold Forming Technology to High-Strength Aluminum Alloy Automotive Parts

A comparative study on cryogenic formability and paint baking property of AA7075 alloy sheets tempered at fast retrogressed and pre-aged conditions

Study on process parameters optimization of 7075-T6 aluminum alloy under contact heating

Investigation on strengthening of 7075 aluminum alloy sheet in a new hot stamping process with pre-cooling

Deformation Behavior and Mechanical Properties of AA7075 During Pre-hardened Aluminum Alloy Hot Forming Process

Modeling mechanical properties and plastic strain for hot forming-quenching AA6061 aluminum alloy parts

Investigation of the Hot Stamping-in-Die Quenching Composite Forming Process of 5083 Aluminum Alloy Skin

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Hot Stamping of a B-Pillar Reinforced Panel With 7075 Aluminum Alloy and the Feasibility Study of Short-Time Aging

Investigation of formability, microstructures and post-forming mechanical properties of heat-treatable aluminum alloys subjected to pre-aged hardening warm forming

Investigation on effect of high-efficiency solid solution and hot stamping process on microstructure evolution and mechanical properties of high-strength aluminum alloy

Strength and Formability Improvement of Al-Cu-Mn Aluminum Alloy Complex Parts by Thermomechanical Treatment with Sheet Hydroforming

Deformation Behavior and Properties of 7075 Aluminum Alloy under Electromagnetic Hot Forming

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Microstructural Evolution and Mechanical Properties of 6082 Aluminum Alloy Automotive Rear Swing Arm Produced by Integrated Process

Microstructure and Properties Evolution of 7075 Al alloy in Hot Rolling and Short Process Heat Treatment