Abstract:The potential of micro electrochemical slotting is significant due to its adaptability and usefulness across diverse manufacturing applications. This technique holds potential, particularly for handling advanced engineering materials like superalloys, with a focus on applications requiring high strength, i.e., micro-cutting for gas-turbine parts, biomedical applications, etc. With this view, this article has been attempted to explore the influence of various considered machining factors, namely as; applied potential difference, tool feed rate (TFR), pulse supply, and modes of tool insulation on the performance measures, i.e. material removal rate (MRR) and surface roughness (Ra) while attempting micro-slotting in Nimonic-263 superalloy work samples. The entire experimentation was conducted on the in-house fabricated 3-axis micro-electrochemical setup designed for performing various complex machining operations at a miniature scale. Furthermore, this study has also been focused toward investigating the impact of varying the electrical conductivity by employing different tool materials (i.e. copper and SS304) on the process characteristics measured. The observed effects of the tool electrode's conductivity have also been expressed and supported by performing the simulation for electric field distribution using COMSOL Multiphysics software. The experimental results have revealed that the process input variables remarkably influence MRR and Ra, mainly applied voltage and TFR. The best values of MRR and Ra attained with SS304 and copper tool electrodes were 1.521 mg/min and 0.721 mg/min, and 0.038 μm and 0.029 μm, correspondingly. The microstructure analysis has further been conducted on machined micro-slotted work samples that provided detailed insights into various surface integrity aspects, which are essential for microdevice applications.

Investigation into micro slotting of Cu-based shape memory alloy via μ-ECM using ethylene glycol mixed aqueous NaCl electrolyte

A Profile Shaping and Surface Finishing Process of Micro Electrochemical Machining for Microstructures on Microfluidic Chip Molds

Study of the electrochemical dissolution behavior of Nitinol shape memory alloy in different electrolytes for micro-ECM process

A performance study of electrochemical micro-machining on SS 316L using suspended copper metal powder along with stirring effect

Simulation and experimental study for enhancing surface integrity of micro-slots processed on Nimonic-263 super alloy via electrochemical machining

Electrochemical Micromachining of NiTi Shape Memory Alloy with Ethylene Glycol–nacl Electrolyte Containing Ethanol

Numerical and experimental analysis of high-aspect-ratio micro-tool electrode fabrication using controlled electrochemical machining

To investigate the effect of discharge energy and addition of nano-powder on processing of micro slots using EDM assisted μ-milling operation

Electrochemical Machining for Micro Holes with High Aspect Ratio on Metal Alloys Using Three-Electrode PPS in Neutral Salt Solution

Improvement of Surface Quality and Machining Depth of μ-ECDM Performances Using Mixed Electrolyte at Different Polarity

Wire electrochemical micromachining of nitinol shape memory alloy using different electrolytes

A hybrid short electric arc and electrochemical machining of the Ti6Al4V alloy

Effect of pulse time (Ton), pause time (Toff), peak current (Ip) on MRR and surface roughness of Cu–Al–Mn ternary shape memory alloy using wire EDM

Sinking ECDM micro-milling of micro-channels with a customized electrode

Selection and Optimization of Electrolyte for Micro Electrochemical Machining on Stainless Steel 304

Research On Micro Ecm Using Micro Array Electrode

Powder mixed micro-electric discharge milling of Ni-rich NiTi SMA: an investigation on machining performance and biocompatibility

Jet Electrochemical Machining of Particle Reinforced Aluminum Matrix Composites with Different Neutral Electrolytes

On high resolution bubbly flow generator for gas-mixed micro electrochemical machining

Experimental examination on electrochemical machining of Mg/FeCoCrNiMn composite

A study of micro-EDM and micro-ECM combined milling for 3D metallic micro-structures