Abstract:Electrochemical machining (ECM) has become more prevalent in titanium alloy processing. However, the presence of the passivation layer on the titanium alloys significantly impacts the performance of ECM. In an attempt to overcome the passivation effects, a high-temperature electrolyte or the addition of halogen ions to the electrolyte has been used. Still, it often results in compromised machining accuracy and surface roughness. This study applied laser and shaped tube electrolytic machining (Laser-STEM) for titanium alloy drilling, where the laser was guided to the machining zone via total internal reflection. The performance of Laser-STEM using different types of electrolytes was compared. Further, the effects of laser power and pulse voltage on the machining side gap, material removal rate (MRR), and surface roughness were experimentally studied while drilling small holes in titanium alloy. The results indicated that the use of passivating electrolytes improved the machining precision, while the MRR decreased with an increase in laser power during Laser-STEM. The MRR showed an increase while using aggressive electrolytes; however, at the same time, the machining precision deteriorated with the increase in laser power. Particularly, the maximum feeding rate of 6.0 mm/min for the tool electrode was achieved using NaCl solution as the electrolyte during Laser-STEM, marking a 100% increase compared to the rate without the use of a laser. Moreover, the model and equivalent circuits were also established to illustrate the material removal mechanisms of Laser-STEM in different electrolytes. Lastly, the processing of deep small holes with a diameter of 1.5 mm, a depth of 38 mm, and a surface roughness of Ra 2 µm was achieved via Laser-STEM without the presence of a recast layer and heat-affected zones. In addition, the cross-inner flow channels in the titanium alloys were effectively processed.

Selection and Optimization of Electrolyte for Micro Electrochemical Machining on Stainless Steel 304

Study on Selection of Electrolyte for Micro Electrochemical Machining on Stainless Steel 304

Electrochemical Machining for Micro Holes with High Aspect Ratio on Metal Alloys Using Three-Electrode PPS in Neutral Salt Solution

Electrochemical dissolution behavior of stainless steels with different metallographic phases and its effects on micro electrochemical machining performance

A performance study of electrochemical micro-machining on SS 316L using suspended copper metal powder along with stirring effect

Experimental Study on the Influence of Tool Electrode Material on Electrochemical Micromachining of 304 Stainless Steel

Electrochemical Machining of Micro-Pit Arrays on a GH4169 Alloy with a Roll-Print Mask Using a C6H5Na3O7-Containing NaNO3 Mixed Electrolyte

Experimental Investigation of Electrochemical Micro-machining Process Parameters on Stainless Steel 316 Using Sodium Chloride Electrolyte

Effect of Anisotropically-etched Silicon Electrode on Electrolytic Products Flow in Micro ECM

Impact of Different Electrolytes on the Machining Rate in ECM Process

Study on the Effect of Electrolytes on Processing Efficiency and Accuracy of Titanium Alloy Utilizing Laser and Shaped Tube Electrochemical Machining

Precision Electrochemical Micro-Machining of Molybdenum in Neutral Salt Solution Based on Electrochemical Analysis

Electrolyte Jet Machining of Ti1023 Titanium Alloy Using NaCl Ethylene Glycol-Based Electrolyte

Deionized Water Electrochemical Machining Hybridized with Alumina Powder Polishing for Microcavity of M-333 Mold Steel

Method for controlling the area of the electrolyte outlets in the flow field simulation and experimental verification of electrochemical machining

Study on Improving Electrochemical Machining Performances through Energy Conversion of Electrolyte Fluid

Multiphysics Research on Electrochemical Machining of Micro Holes with Internal Features

Improvement of Surface Quality and Machining Depth of μ-ECDM Performances Using Mixed Electrolyte at Different Polarity

Analysis and Experimental Study of Micro ECM with Intermittent Retraction of Electrode

Improvement of machining quality by using axial supplementary electrolyte in electrochemical cutting with radial electrolyte flushing

Influence of Electrolytic Products in Machining Gap on Micro ECM