Abstract:Abstract Precision machining is becoming more and more important with the increasing demands on surface quality for various components. This applies, for example, to mirror components in micro-optics or cooling components in microelectronics. Copper is a frequently used material for this purpose, but its mechanical properties make it difficult to machine. In this study, a process strategy for finishing copper surfaces with batch-manufactured micro-grinding tools in an electrochemically assisted grinding process is demonstrated. The tool heads are manufactured from a polyimide-abrasive-suspension and silicon as a carrier substrate using microsystems technology. The matching shafts are milled from aluminium. The tools are then used on pure copper and oxidised copper surfaces. By using finer abrasives grains (1.6–2.4 μm instead of 4–6 μm) than previously, similar surface roughness values could be achieved ( R a = 0.09 ± 0.02 μm, R z = 1.94 ± 0.73 μm) with the same grinding process. An optimised grinding process that combines the use of rough and fine tools, on the other hand, achieves significantly better surface finishes in just four grinding iterations ( R a = 0.02 ± 0.01 μm, R z = 0.83 ± 0.21 μm). In order to achieve a further increase in surface quality, this optimised grinding process is combined with the anodic oxidation of the copper workpieces. The surface modification is done to increase the machinability of the surface by creating an oxide layer. This is confirmed by the results of scratch tests carried out, which showed less force acting on the tool during machining with the oxide layer than with a pure copper surface. To realise this within the machine tool, an electrochemical cell is shown that can be integrated into the machine so that the oxidation can be carried out immediately before the grinding process. The copper layers produced inside the electrochemical cell in the machine tool show similar characteristics to the samples produced outside. Processing the oxidised samples with the optimised grinding process led to a further reduction of about 17% in the R z values ( R a = 0.03 ± 0.01 μm, R z = 0.69 ± 0.20 μm). The combination of the shown grinding process and the integration of anodic oxidation within the machine tool for the surface modification of copper workpieces seems to be promising to achieve high surface finishes.

Ultrasonic assisted electropolishing to reduce the surface roughness of laser powder bed fusion based additively manufactured copper heat exchanger components

Investigation of surface roughness post-processing of additively manufactured nickel-based superalloy Hastelloy X using electropolishing

Material Removal and Surface Modification of Copper under Ultrasonic-Assisted Electrochemical Polishing

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

On the Optimization of Roughness and Corrosion Resistance of Laser Beam Powder Bed Fusion Fabricated Ti–6Al–4V Parts—An Electrochemical Approach

Surface Polishing of Laser Powder Bed Fused Inconel 625 Surfaces Using Multi-jet Hydrodynamic Cavitation Abrasive Finishing: An Emerging Class of Cleaner Surface Enhancement Process

High-quality surface smoothening of laser powder bed fusion additive manufacturing AlSi10Mg via intermittent electrochemical polishing

Development of a magnetically driven abrasive polishing process for additively manufactured copper structures

Two-Steps Electrochemical Polishing of Laser Powder Bed Fusion 316L Stainless Steel

Novel multiphase jet polishing for complicated structured components produced by laser powder bed fusion

Electrochemical polishing with glycol-based electrolyte of the curved internal channels fabricated via laser powder bed fusion

Fabrication of Smooth, Periodic Surface Structures: Combining Direct Laser Interference Patterning and Electropolishing

Detailed characterisation of batch-manufactured flexible micro-grinding tools for electrochemical assisted grinding of copper surfaces

A new polishing method for complex structural parts: moist particle electrolyte electrochemical mechanical polishing (MPE-ECMP)

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Intentional Oxidation and Laser Remelting of Highly Reflective Pure Cu for Its High‐Quality Additive Manufacturing

Electrorheological fluid–assisted ultrasonic polishing for IN625 additively manufactured surfaces

Laser Powder Bed Fusion of Copper-Tungsten Powders Manufactured by Milling or Co-Injection Atomization Process

High-precision laser powder bed fusion processing of pure copper

Laser powder bed fusion of electrically/thermally conductive component by developing inert Cr 2 O 3 -coated Cu powder

Process-Structure-Property Relationships of Copper Parts Manufactured by Laser Powder Bed Fusion