Abstract:The processing of pure copper (Cu) has been a challenge for laser-based additive manufacturing for many years since copper powders have a high reflectivity of up to 83% of electromagnetic radiation at a wavelength of 1070 nm. In this study, Cu particles were coated with sub-micrometer tungsten (W) particles to increase the laser beam absorptivity. The coated powders were processed by powder bed fusion-laser beam for metals (PBF-LB/M) with a conventional laser system of <300 watts laser power and a wavelength of 1070 nm. Two different powder manufacturing routes were developed. The first manufacturing route was gas atomization combined with a milling process by a planetary mill. The second manufacturing method was gas atomization with particle co-injection, where a separate W particle jet was sprayed into the atomized Cu jet. As part of the investigations, an extensive characterization of powder and additively manufactured test specimens was carried out. The specimens of Cu/W powders manufactured by the milling process have shown superior results. The laser absorptivity of the Cu/W powder was increased from 22.5% (pure Cu powder) to up to 71.6% for powders with 3 vol% W. In addition, a relative density of test specimens up to 98.2% (optically) and 95.6% (Archimedes) was reached. Furthermore, thermal conductivity was measured by laser flash analysis (LFA) and thermo-optical measurement (TOM). By using eddy current measurement, the electrical conductivity was analyzed. In comparison to the Cu reference, a thermal conductivity of 88.9% and an electrical conductivity of 85.8% were determined. Moreover, the Vickers hardness was measured. The effect of porosity on conductivity properties and hardness was investigated and showed a linear correlation. Finally, a demonstrator was built in which a wall thickness of down to 200 µm was achieved. This demonstrates that the Cu/W composite can be used for heat exchangers, heat sinks, and coils.

Laser powder bed fusion of electrically/thermally conductive component by developing inert Cr 2 O 3 -coated Cu powder

Preparation of Cu-Cr-Zr Alloy by Laser Powder Bed Fusion: Parameter Optimization, Microstructure, Mechanical and Thermal Properties for Microelectronic Applications

Laser-beam powder bed fusion of Al–Fe–Cu alloy to achieve high strength and thermal conductivity

Manufacturing of High Strength and High Conductivity Copper with Laser Powder Bed Fusion

Laser Cladding Fe/FeCr Coatings on Continuous Casting Cu Mold

Laser Powder Bed Fusion of Copper-Tungsten Powders Manufactured by Milling or Co-Injection Atomization Process

Fabrication of Copper Alloys as Conductive Materials via Laser Beam Powder Bed Fusion

High-strength and High-Conductivity Additively Manufactured Cu-O Alloy Enabled by Cellular Microstructure

Mechanism of Simultaneous Improvement of Mechanical Performance and Conductivity of TiC/Cu Composites Prepared by Laser Powder Bed Fusion

Intentional Oxidation and Laser Remelting of Highly Reflective Pure Cu for Its High‐Quality Additive Manufacturing

Fabrication of a Strong and Ductile CuCrZr Alloy Using Laser Powder Bed Fusion

Laser Powder Bed Fusion of Metal Coated Copper Powders

Laser powder bed fusion of a Cu-Ni-Al alloy using the compositional grading approach

Laser powder bed fusion of copper matrix iron particle reinforced nanocomposite with high strength and high conductivity

Progress in laser powder bed fusion of pure copper/copper alloy highly reflective metal materials

Laser powder bed fusion of in-situ amorphous oxide dispersion strengthened immiscible Cu-316 L bimetallic composite: Formation mechanism and current-carrying wear behavior

High Reflectivity and Thermal Conductivity Ag–Cu Multi-Material Structures Fabricated via Laser Powder Bed Fusion: Formation Mechanisms, Interfacial Characteristics, and Molten Pool Behavior

On thermal properties of metallic powder in laser powder bed fusion additive manufacturing

Composition design method of Al-Cu alloy for laser powder bed fusion

Copper alloys for additive manufacturing: Laser powder bed fusion of CuCr1Zr by using a green qcw-laser

Modification of Electrical and Mechanical Properties of Selective Laser‐Melted CuCr0.3 Alloy Using Carbon Nanoparticles