Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Particle-stimulated nucleation and recrystallization texture initiated by coarsened Al2CuLi phase in Al–Cu–Li alloy

Structural Evolution of Topologically Closed Packed Phase in a Ni-based Single Crystal Superalloy

Effect of Dynamic Recrystallization Mode on Texture Components and Hardness for Nano-SiC Particles Reinforced Aluminum Matrix Composites Prepared Via Friction Stir Processing

Enhanced grain refinement and texture weakening in Al–Mg–Si alloy through a novel thermomechanical processing

Minimum Interface Misfit Criterion for the Precipitation Morphologies of TCP Phases in a Ni-based Single Crystal Superalloy

Formation Mechanism of Cube Texture Components ({001}<100>) Associated with Dynamic Recrystallization During Compression in the Single BCC Phase Region of Ti-22Al-25Nb Alloy

T1 precipitate bands and particle stimulated nucleation in 2195 Al-Cu-Li alloy during hot deformation

Formation mechanism of Cube texture components ({001} ) associated with dynamic recrystallization during compression in the single BCC phase region of Ti-22Al-25Nb alloy

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Micro-nano structure characteristics and texture evolution of the friction stir processed dual-phase Mg Li alloy

Texture evolution of refill friction stir spot welding in alclad 2A12-T42 aluminum alloy

Microstructure and Texture Evolution of Particle-Containing Aa3104 Alloy Cold Rolled to Large Strains

Coarsening kinetics of γ′ phase in isothermal aged high Al content Ni–17 at.% Al alloy

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Precipitation behavior and its effect on the dynamic recrystallization of a novel extruded Al-Cu-Li alloy

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

In-situ observations of static recrystallization and texture formation in a cold-rolled CoCrFeMnNi high entropy alloy

Systematic investigation of the texture evolution of Cu-Ni alloys with different strains

Effects of Icosahedral Phase on Mechanical Anisotropy of As-Extruded Mg-14Li (in Wt%) Based Alloys

Formation and development of Goss texture in Al–Cu–Mg alloy during solution treatment

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences