Abstract:Mg–1Mn alloy, extruded at a low temperature in our published protocol, contributed to the intensified basal texture and extremely refined microstructure with spheroidal nanoscale precipitates dispersing throughout the matrix and along the grain boundaries, consequently resulting in the excellent mechanical properties where the alloy exhibited a tensile yield strength of 204.3 MPa and a ductility of 38.8% at room temperature. Therefore, Mg–1Mn alloy was recommended as one of the potential materials for structural applications. In the present investigation, hot deformation behavior through constitutive analysis and extrusion temperature-dependent microstructure, texture and mechanical properties of as-extruded Mg–1Mn alloy were investigated, aiming at revealing how extrusion temperature affected microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. X-ray diffraction patterns demonstrated that phase components of the experimental alloys consisted of the α-Mg matrix and Mn precipitates. Optical microscopy images indicated a significant increase in average grain size of the alloys as the extrusion temperature increasing from 250 °C to 400 °C. Scanning electron microscopy graphics revealed that coarsened particles identified as Mn precipitates by EDS were observed within the matrix when extrusion temperature reached 400 °C. Inverse pole figure maps of the experimental samples subjected to different extrusion temperatures in the present work exhibited the typical basal texture, suggesting that basal slip was activated hardly during the tensile stress applied along the extrusion direction. Consequently, extrusion temperature displayed the significant impact on microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. The alloy extruded at both 250 °C and 300 °C exhibited the strong basal texture and refined microstructure with spheroidal nanoscale precipitates dispersing within the matrix and along the grain boundaries, which contributed to their excellent comprehensive mechanical properties. The alloy extruded at 400 °C possessed the typical basal texture and coarsened microstructure, leading to the extremely poor mechanical properties. Simultaneously, the constitutive model of the Arrhenius equation based on Zener-Hollomon parameters was also established in the present investigation. Therefore, optimizing the extrusion temperature to regulate the microstructure, grain orientation distribution, and morphology of precipitates was considered as one of the effective approaches for achieving the excellent mechanical properties of Mg alloys.

Effects of extrusion temperature on microstructure evolution and mechanical properties of heterogeneous Mg−Gd alloy laminates via accumulated extrusion bonding

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Effect of Extrusion Parameters on Microstructure and Mechanical Properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) Alloy

Deformation behaviors and the related high-temperature mechanical properties of Mg-11Gd-5Y-2Zn-0.7Zr via regulating extrusion temperatures

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures

Effect of extrusion temperature on the microstructure and mechanical properties of Mg97Y2Zn1 alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Effect of extrusion temperature on microstructure, mechanical properties, and deformation mechanism of Mg-2.5Er-0.6Zr alloy

Effect of extrusion temperature on microstructure and mechanical properties of Mg-8.5Gd-2.3Y-l.8Ag- 0.4Zr alloy solid state recycled by hot extrusion

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Study on the Mutual Effect of La and Gd on Microstructure and Mechanical Properties of Mg-Al-Zn Extruded Alloy

Microstructure and tensile properties of a low-alloyed magnesium alloy: effect of extrusion temperature

Hot deformation behavior and extrusion temperature-dependent microstructure, texture and mechanical properties of Mg–1Mn alloy

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

A Preliminary Study on the Effects of Aging Temperature on the Microstructure and Mechanical Properties of As-Extruded Mg-12Gd-4Y-1Zn Magnesium Alloy

Microstructures and Mechanical Properties of Extruded Mg-9Gd-4Y-0.6Zr-T5 at Elevated Temperatures

High Temperature Deformation and Microstructural Evolution of Mg–Gd–Y Alloys

Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg–Zn–Gd–Y–Zr alloy