Abstract:The recycled Mg–Al–Zn alloys are successfully fabricated through solid‐state recycling of mixed waste chips, including cold pressing and hot extrusion. The recycled Mg–Al–Zn alloys at 350 °C demonstrate excellent mechanical properties with the yield strength of 134.6 MPa, ultimate tensile strength of 286.2 MPa, elongation of 7.4%, and Vickers hardness of 75.2 HV, respectively. The recycled Mg–Al–Zn alloys are successfully fabricated through solid‐state recycling of mixed waste chips, including cold pressing and hot extrusion. The effects of extrusion temperature on the microstructure evolution, slip mode, tensile properties, and hardness are studied. The homogeneous fine dynamic recrystallization (DRXed) grains with an average grain size of less than 13.1 μm can be obtained at four different extrusion temperatures (250, 300, 350, and 400 °C). The average grain size of the DRXed grains continuously increases with the rising extrusion temperature. However, the yield strength (YS), ultimate tensile strength (UTS), and elongation to failure (EL) of the recycled alloys increase first and then decrease. The recycled Mg–Al–Zn alloys at 350 °C demonstrate excellent mechanical properties with the YS of 134.6 MPa, UTS of 286.2 MPa, EL of 7.4%, and Vickers hardness of 75.2 HV, respectively. In addition, the slip mode is transformed from the previous basal slip to the coactivation of multiple slips composed of the basal slip, prismatic slip, and pyramidal slip with the rising extrusion temperature.

Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg–Zn–Gd–Y–Zr alloy

Effect of extrusion process on microstructure and mechanical and corrosion properties of biodegradable Mg−5Zn−1.5Y magnesium alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Effect of Extrusion Process on Microstructure, Corrosion Properties, and Mechanical Properties of Micro-Alloyed Mg–Zn–Ca–Zr Alloy

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys

A newly developed Mg-Zn-Gd-Mn-Sr alloy for degradable implant applications: Influence of extrusion temperature on microstructure, mechanical properties and in vitro corrosion behavior

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

Effect of Extrusion on Mechanical Property, Corrosion Behavior, and In Vitro Biocompatibility of the As-Cast Mg-Zn-Y-Sr Alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Effect of extrusion process on the mechanical and in vitro degradation performance of a biomedical Mg-Zn-Y-Nd alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Effect of temperature on the microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr alloy during the large height-to-diameter ratio upsetting and extrusion

Microstructure, mechanical properties and corrosion fatigue behaviour of biodegradable Mg–Zn–Y–Nd alloy prepared by double extrusion

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Influence of Extrusion Temperature on Microstructure and Mechanical Properties of Mg-4Y-4Sm-0.5Zr Alloy

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Enhanced Mechanical Properties and Corrosion Resistance by Minor Gd Alloying with a Hot-Extruded Mg Alloy

Corrosion behavior and mechanical properties of extruded low-alloyed Mg−0.5Bi−0.5Y−0.2Zn alloy

Effect of Extrusion Temperature on Microstructure and Mechanical Properties of Mg–Al–Zn Alloy Prepared by Solid‐State Recycling of Mixed Waste Chips