Abstract:Deformation processing is a commonly used strategy to improve the microstructure and hence mechanical properties of biodegradable Zn alloys. However, a single conventional processing method is usually limited in achieving this goal. In this work, hot extrusion combined with room-temperature equal channel angular pressing (ECAP) was used to fabricate biodegradable Zn–Cu–Li alloy. Compared to the hot-extruded alloy, the further ECAPed alloys have significantly finer Zn grains and precipitate more submicron- and nano-sized ε -CuZn 4 particles. Moreover, the 4-pass as-ECAPed alloy exhibits the best comprehensive mechanical properties with yield strength of 315 ± 3 MPa, ultimate tensile strength of 444 ± 13 MPa and elongation of 81 ± 5%, which are 13.3%, 38.8% and 72.3% higher than those of the hot-extruded alloy, respectively. In addition, in vitro and in vivo tests were performed on the 4-pass as-ECAPed alloy to evaluate its corrosion behavior, antibacterial property, cytotoxicity and biocompatibility. In vitro results showed that the 4-pass as-ECAPed alloy exhibits better corrosion resistance than the 8-pass alloy. Also, it shows good antibacterial property, hemocompatibility and cytocompatibility. In vivo results demonstrated that the 4-pass as-ECAPed alloy exhibits faster and more uniform degradation than the pure Zn (as a control group). Both the pure Zn and 4-pass as-ECAPed alloy promote formation of new bone, the mass of which increases over time. The 4-pass as-ECAPed alloy shows slightly weaker osteogenic capacity but better overall osteointegration than the pure Zn. Furthermore, both the pure Zn and 4-pass as-ECAPed alloy exhibit good in vivo biosafety.

Effect of extrusion process on the mechanical and in vitro degradation performance of a biomedical Mg-Zn-Y-Nd alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Optimization of Microstructure and Mechanical Property of a Mg-Zn-Y-Nd Alloy by Extrusion Process

Optimizing Mechanical Property and Cytocompatibility of the Biodegradable Mg-Zn-Y-Nd Alloy by Hot Extrusion and Heat Treatment

Effect of original grain size on microstructure and properties of extruded Mg-2Zn-0.2Mn biomedical alloy

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Microstructure, mechanical properties and corrosion fatigue behaviour of biodegradable Mg–Zn–Y–Nd alloy prepared by double extrusion

Effect of Extrusion on Mechanical Property, Corrosion Behavior, and In Vitro Biocompatibility of the As-Cast Mg-Zn-Y-Sr Alloy

Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg–Zn–Gd–Y–Zr alloy

Microstructural Characteristics and Mechanical Properties of the Hot Extruded Mg-Zn-Y-Nd Alloys

Effect of extrusion process on microstructure and mechanical and corrosion properties of biodegradable Mg−5Zn−1.5Y magnesium alloy

Influence of Multi-Pass Hot Extrusion on Microstructure and Mechanical Properties of the Mg–4Zn–1.2Y–0.8Nd Alloy

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

The Effect of Heat Treatment and Extrusion on Microstructure and Properties of Medical Mg-1Mn-2Zn Alloy

Effects of backward extrusion on mechanical and degradation properties of Mg-Zn biomaterial.

Hot Extrusion Effect on the Microstructure and Mechanical Properties of a Mg–Y–Nd–Zr Alloy

Effect of Extrusion Process on Microstructure, Corrosion Properties, and Mechanical Properties of Micro-Alloyed Mg–Zn–Ca–Zr Alloy

A newly developed Mg-Zn-Gd-Mn-Sr alloy for degradable implant applications: Influence of extrusion temperature on microstructure, mechanical properties and in vitro corrosion behavior

An in vitro and in vivo study of biodegradable Zn–Cu–Li alloy with high strength and ductility fabricated by hot extrusion combined with room-temperature ECAP