Abstract:Highlights • Effects of microstructure inhomogeneity on tensile deformation behavior of ZK60 Mg were clarified. • Tensile temperature and loading direction determined the slipping- or twinning-dominated deformation mode. • DRX was changed from continuous mode to discontinuous mode with increasing tensile temperature. • Welding zone showed superplastic behavior at tensile temperature > 300 °C due to the GBS effects. • The texture evolution was dependent on loading direction, tensile temperature and recrystallization mode. The tensile tests of the extruded ZK60 Mg containing a longitudinal weld seam were carried out at room and elevated temperatures, and the effects of induced microstructure inhomogeneity on tensile deformation behavior was clarified. The results show that the deformation mode, dynamic recrystallization (DRX), texture evolution and mechanical properties are strongly affected by the longitudinal weld seam, temperature, and loading direction. The room temperature (RT) deformation of welding zone is controlled by the dislocation slips with the association of some twins, while twinning plays significant roles in the accommodation of c -axis strain of the coarse grains on matrix zone. The deformation at RT stretched along extrusion direction (ED) and transverse direction (TD) are controlled by basal slip/twinning and basal slip/prismatic slip/twinning, respectively. During high temperature tension, the dislocation cross slip of pyramidal slip is activated, and grain boundary sliding occurred in welding zone, leading to the superplastic behavior. With the increase of tensile temperature, the predominant DRX mode is transformed from continuous DRX to discontinuous DRX. Moreover, the basal poles of the grains spread from TD towards ED with the decrease of maximum pole intensity when stretched along ED, while non-basal textures are transformed to 〈10–10〉 fiber texture when stretched along TD. The slip-dominated flow is seen during RT tension along ED, while twinning becomes predominant during RT tension along TD. The fine grain structure causes the superior RT tensile properties along ED of welding zone with ultimate tensile strength of 315 MPa and elongation to failure of 13.8%. With the increase of tensile temperature, the slipping-dominated deformation is transformed into twinning-dominated, causing the decrease of strength and increase of elongation.

Microstructure characterization and corrosion behavior of hollow ZK60 Mg profile containing longitudinal welds

Evolution mechanisms of charge weld during porthole die extrusion of ZK60 Mg profile

Effect of Extrusion Process on Microstructure, Corrosion Properties, and Mechanical Properties of Micro-Alloyed Mg–Zn–Ca–Zr Alloy

Microstructure and Corrosion of Cast Magnesium Alloy ZK60 in NaCl Solution

Formation of abnormal coarse grains and its effects on corrosion behaviors of solution treated ZK60 Mg alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Microstructure and mechanical properties of longitudinal weld in 6005A aluminum alloy profile extruded by a porthole die

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

Microstructure evolution and corrosion behavior of TIG welded joint of a new Mg Gd Nd Zn Zr alloy during post-weld heat treatment

Experimental study on tensile deformation behaviors under room and elevated temperatures induced by microstructure inhomogeneity of ZK60 Mg with a longitudinal weld

Microstructure and mechanical properties of extrusion ZC61 alloys under different dynamic compression loading directions

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

Microstructure evolution difference in Mg96.5Gd2.5Zn1 alloys extruded from as-cast and solution-treated states

Microstructure Evolution of ZK61m Magnesium Alloy Sheet during Erichsen Test

Investigation of the microstructure and properties of extrusion-shear deformed ZC61 magnesium alloy under high strain rate deformation

Effects of welding angle on microstructure and mechanical properties of longitudinal weld in 6063 aluminum alloy extrusion profiles

On the heterogeneous microstructure and strengthening mechanisms in a laser welding AZ80 magnesium alloy

Study on Corrosion Characteristics and Mechanism of Laser Powder Bed Fusion of Mg-Zn-Zr Alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

Microstructure and Mechanical Properties of As-Cast and Hot Extruded–Sheared ZG61 Alloy