Abstract:Highlights • Effects of microstructure inhomogeneity on tensile deformation behavior of ZK60 Mg were clarified. • Tensile temperature and loading direction determined the slipping- or twinning-dominated deformation mode. • DRX was changed from continuous mode to discontinuous mode with increasing tensile temperature. • Welding zone showed superplastic behavior at tensile temperature > 300 °C due to the GBS effects. • The texture evolution was dependent on loading direction, tensile temperature and recrystallization mode. The tensile tests of the extruded ZK60 Mg containing a longitudinal weld seam were carried out at room and elevated temperatures, and the effects of induced microstructure inhomogeneity on tensile deformation behavior was clarified. The results show that the deformation mode, dynamic recrystallization (DRX), texture evolution and mechanical properties are strongly affected by the longitudinal weld seam, temperature, and loading direction. The room temperature (RT) deformation of welding zone is controlled by the dislocation slips with the association of some twins, while twinning plays significant roles in the accommodation of c -axis strain of the coarse grains on matrix zone. The deformation at RT stretched along extrusion direction (ED) and transverse direction (TD) are controlled by basal slip/twinning and basal slip/prismatic slip/twinning, respectively. During high temperature tension, the dislocation cross slip of pyramidal slip is activated, and grain boundary sliding occurred in welding zone, leading to the superplastic behavior. With the increase of tensile temperature, the predominant DRX mode is transformed from continuous DRX to discontinuous DRX. Moreover, the basal poles of the grains spread from TD towards ED with the decrease of maximum pole intensity when stretched along ED, while non-basal textures are transformed to 〈10–10〉 fiber texture when stretched along TD. The slip-dominated flow is seen during RT tension along ED, while twinning becomes predominant during RT tension along TD. The fine grain structure causes the superior RT tensile properties along ED of welding zone with ultimate tensile strength of 315 MPa and elongation to failure of 13.8%. With the increase of tensile temperature, the slipping-dominated deformation is transformed into twinning-dominated, causing the decrease of strength and increase of elongation.

Evolution mechanisms of charge weld during porthole die extrusion of ZK60 Mg profile

Microstructure characterization and corrosion behavior of hollow ZK60 Mg profile containing longitudinal welds

Integrated Physical and Numerical Simulations of Weld Seam Formation During Extrusion of Magnesium Alloy

Microstructure and mechanical properties of longitudinal weld in 6005A aluminum alloy profile extruded by a porthole die

Evolution of grain structure, texture and mechanical properties of a Mg–Zn–Zr alloy in bobbin friction stir welding

Effects of welding angle on microstructure and mechanical properties of longitudinal weld in 6063 aluminum alloy extrusion profiles

Microstructure Development and Texture Evolution of Aluminum Multi-Port Extrusion Tube During the Porthole Die Extrusion

An extrusion-welding criterion of magnesium alloy considering interfacial void shrinkage driven by plastic deformation and atomic diffusion

Optimization design of porthole die and study on microstructures and mechanical properties for an Al–Li alloy hollow profile

Physical Simulation Method for the Investigation of Weld Seam Formation During the Extrusion of Aluminum Alloys

Severely Weakened Extrusion Strengthening Effect in Porthole Die Extrusion of Al-Mg-Si Alloy Miniature Complex Hollow Profile under an Ultra-Large Extrusion Ratio

Effect of microstructural evolution on mechanical properties of friction stir welded ZK60 alloy

Evolution Of The Material Microstructures And Mechanical Properties Of Aa1100 Aluminum Alloy Within A Complex Porthole Die During Extrusion

Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multi-cavity complex section and analysis of profile performance

Investigation into Atomic Diffusion at the Interface During Extrusion Welding of Magnesium and Magnesium Alloys

Experimental study on tensile deformation behaviors under room and elevated temperatures induced by microstructure inhomogeneity of ZK60 Mg with a longitudinal weld

Macrostructure, Microstructure and Mechanical Properties of Bobbin Tool Friction Stir Welded ZK60 Mg Alloy Joints

Weld Morphology and Grain Growth Characteristics of Driven Moving Arc Hollow Stud Welding

Dissimilar ultrasonic spot welding of rare-earth containing ZEK100 magnesium-to-aluminum alloy with a zinc interlayer: Microstructural evolution and mechanical properties

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Effects of Zn, Mg, and Cu Content on the Properties and Microstructure of Extrusion-Welded Al-Zn-Mg-Cu Alloys