Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Effect of strain and dispersoids on abnormal grain growth, precipitation behavior and mechanical properties at longitudinal weld in Al-Li alloy profile

Effects of Cold Rolling Pre-Strain on Abnormal Grain Growth Behavior in Longitudinal Welds of 2196 Al-Cu-Li Profiles

Intermediate annealing treatment as an effective tool for suppression of abnormal grain growth at longitudinal weld of 2196 Al–Cu–Li profile

Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy

Improving joint performance of friction stir welded 2195-O Al–Li alloy by post-weld heat treatment and rolling deformation

Investigation on hot deformation behavior and quenching precipitation mechanism of 2195 Al-Li alloy

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Effect of grain thickness and T 1 precipitate on the strength anisotropy of Al-4.0Cu-1.0Li-0.4Mg-0.4Ag-xZr alloys under different heat treatment

Microstructure and mechanical properties of longitudinal weld in 6005A aluminum alloy profile extruded by a porthole die

Microstructural evolution and mechanical properties of the rapidly-solidified and hot-extruded 2196 Al-Li alloy

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Influence of pre-stretching at ambient and cryogenic temperatures on dislocation configuration, precipitation behaviour, and mechanical properties of 2195 Al-Cu-Li alloy

Dynamic precipitation and its effect on microstructure of 2195 Al–Li alloy during medium/high temperature deformation

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Effect of heat treatment on hot deformation behavior and microstructure evolution of 2195 Al-Li alloy

A Modified Constitutive Model and Microstructure Characterization for 2195 Al-Li Alloy Hot Extrusion

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Constitutive Analysis and Microstructure Characteristics of As-Homogenized 2198 Al–Li Alloy under Different Hot Compression Deformation Conditions

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Optimizing mechanical property of spray formed Al-Zn-Mg-Cu alloy by combination of homogenization and warm-rolling