Abstract:To enhance the ablation resistance of Ti6Al4V alloy, a SiC-modified nanocomposite ceramic coating was fabricated by a novel one-step liquid plasma-assisted particle deposition sintering (LPDS) method. A microarc oxidation (MAO) ceramic coating was prepared on the surface of titanium alloy as a comparison. The micromorphologies and formation mechanisms of two ceramic coatings were investigated with the assistance of scanning electron microscopy (SEM), X-ray diffractometer (XRD), and transmission electron microscopy (TEM). The thickness of the SiC nanocomposite coating (about 39 μm) was significantly increased by 129% compared to the MAO coating (about 17 μm). Additionally, ablation tests of Ti6Al4V alloy, MAO coating, and SiC nanocomposite coating were conducted at 1000 °C using a butane gas lance. Then, the variation of microstructure, phases, elemental composition, and thickness before and after ablation was also comparatively analyzed. The results indicate that the SiC nanocomposite coating exhibits the smallest thickening (29 μm) after ablation at 1000 °C for 360 s, which is 39% and 46% compared with the Ti6Al4V substrate and MAO coating, respectively. The nanocomposite coating is intact and cracks-free after the ablation test. SiO 2 , formed during the ablation of SiC nanocomposite coatings, blocks oxygen diffusion into the substrate, which plays a protective role in the coating. Therefore, the SiC nanocomposite coating by a novel LPDS technique exhibits superior ablation resistance to enhance the thermal protection performance of titanium alloy substrate.

Effect of Si, Al2O3 additives on the ablation behavior of ZrB2-SiC coating with Al2O3-modified SiC bond coat for C/C composites

Anti-ablation Performance of Plasma Sprayed ZrB2/SiC Coatings on C/C Substrates and the Influence of a Chemical Vapor Deposited SiC Interlayer

Anti-ablation performance of plasma sprayed ZrB 2 /SiC coatings on C/C substrates and the influence of a chemical vapor deposited SiC interlayer

Microstructure and Ablation Performance of SiC–ZrC Coated C/C Composites Prepared by Reactive Melt Infiltration

Effect of Al2O3 addition on the microstructure and oxidation behavior of SiC coating prepared by pack cementation on C/C composites

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Oxidation ablation resistance of ZrB2-HfB2-SiC-TaSi2 coating prepared on C/C composite surface

Microstructure, surface stress and surface temperature response of ZrB2–SiC based coatings

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Influences of deposition temperature, gas flow rate and ZrC content on the microstructure and anti-ablation performance of CVD-HfC-ZrC coating

Effects of SiC on microstructure and properties of plasma sprayed ZrB2–ZrC composite coating

Ablation mechanism and morphology evolution of the HfC-SiC coating for C/C composites deposited by supersonic atmospheric plasma spraying

Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation

Ablation resistance of SiC-modified nanocomposite ceramic coating prepared by LPDS method on titanium alloy

Ablation behavior of ZrC-SiHfOC-MoSi 2 coating for carbon/carbon composites under Ar-O 2 plasma flame

Ablation behavior of ZrB2–SiC–Si composites with WC and MoSi2 additives coated through SPS on graphite

Preparation and characterization of monolayer oxidation resistant coating on C/SiC composites

Self-densification behavior, interfacial bonding and cyclic ablation resistance of HfSi2-ZrSi2 modified SiC/ZrB2-SiC/SiC coating for Cf/SiC composite

Ablation behaviour of the CVD-(ZrC/SiC)3 alternate coating on C/C composites under oxyacetylene torch with different heat fluxes

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites