Abstract:In this study, Ti–Si–C composite coatings were synthesized via plasma spraying of agglomerated powders prepared by a spray drying/precursor pyrolysis technology using Ti, Si, and sucrose powders. The influence of Si content, ranging from 0 wt% to 24 wt%, on the microstructure, mechanical properties, and oxidation resistance of the composite coatings was investigated. Results show that the phase composition of the Ti–Si–C composite coatings changes with the increasing Si content. The coatings without Si addition consist of TiC and Ti3O; the coatings with 6–18 wt% Si are composed of TiC, Ti5Si3, and Ti3O; the coatings with Si content of 24 wt% form only TiC and Ti5Si3 phases. As the Si content increases, the hardness of the Ti–Si–C composite coatings increases first and then decreases, depending on the intrinsic hardness of the ceramic phases, the brittleness of Ti5Si3, and the defects such as pores and cracks. The Ti–Si–C composite coatings have high wear resistance due to the in-situ synthesized high-hardness TiC and Ti5Si3. Owing to the high brittleness of Ti5Si3, the increasing Si content leads to higher wear volume loss at room temperature, which can be partially improved in high-temperature wear tests. The oxidation resistance of Ti–Si–C composite coatings increases with the increase of Si content, and the higher the oxidation temperature, the more obvious the influence of the Si addition on oxidation resistance.

Effects of SiC on microstructure and properties of plasma sprayed ZrB2–ZrC composite coating

Microstructure and properties of in-situ ZrB2-ZrC composite coatings by plasma spraying

Microstructure and properties of Cr7C3-CrSi2 composite coatings prepared by plasma spraying

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Low-pressure plasma spraying of ZrB2-SiC coatings on C/C substrate by adding TaSi2

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Effect of Si, Al2O3 additives on the ablation behavior of ZrB2-SiC coating with Al2O3-modified SiC bond coat for C/C composites

Synthesis of In Situ ZrB2-SiC-ZrC Coating on ZrC-SiC Substrate by Reactive Plasma Spraying

Effect of Si content on the microstructure and properties of Ti–Si–C composite coatings prepared by reactive plasma spraying

Effect of SiC Deposition Behavior on Microstructure and Mechanical Properties of Cold-Sprayed Al5056/SiC Composite Coatings

Oxidation ablation resistance of ZrB2-HfB2-SiC-TaSi2 coating prepared on C/C composite surface

Plasma sprayed TiC–Ti5Si3–Ti3SiC2 composite coatings from Ti–SiC-graphite powders with different SiC particle size

Microstructure, surface stress and surface temperature response of ZrB2–SiC based coatings

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Anti-ablation Performance of Plasma Sprayed ZrB2/SiC Coatings on C/C Substrates and the Influence of a Chemical Vapor Deposited SiC Interlayer

TEM characterization and reaction mechanism of composite coating fabricated by plasma spraying Nb–SiC composite powder

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Microstructure and Thermal Properties of Inert Plasma-Sprayed Tungsten Coating on SiC-Coated Carbon/Carbon Composites

Microstructure and properties of molybdenum composite coatings by plasma spraying of Mo–SiC and MoO 3 –Al–SiC composite powders

Anti-ablation performance of plasma sprayed ZrB 2 /SiC coatings on C/C substrates and the influence of a chemical vapor deposited SiC interlayer