Abstract:In the present study, titanium carbide powders with suitable morphology and nanometer particle size were synthesized by the sol-gel method to investigate the parameters affecting the properties of sol and the final powder. The initial sol was prepared in a four-component system of alkoxide-water-alcohol-citric acid based on the chemical process of sol-gel. study of sol properties showed that pH was the most important factor in the control of sol conditions and particle size so that at low pHs, due to low concentration of OH- ions and reduced viscosity, it was easier to control the particles size. Accordingly, the results of the Dynamics Light Scattering (DLS) showed that at low pHs, the particles size was below 10 nm. According to the zeta potential diagram and by examining the conditions of sol at different pHs, 4.5 was determined as the optimal pH and to prevent the bonding of particles within the sol, ammonium polycarboxylate dispersant was used. The temperature at which particles were formed was determined using Differential thermal analysis (DTA) and Thermal gravimetric analysis (TG). X-ray diffraction (XRD) patterns showed the presence of a completely amorphous phase at 700 ̊C. It was also observed that with increasing temperature, TiC crystallization started from 1200 ̊C and ended at 1400 ̊C. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) micrographs at 1400 ̊C showed the completely spherical morphology of particles of nanometer size so that no agglomerate was observed.

A New Sight on The Influence of Molten Salt in The Preparation of (Ta, Nb, Ti) C Nano‐Powder

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

Influence of (Ta Nb Ti V) C powders synthesized by molten salt at low temperature on densification and properties of high entropy carbide ceramics

Synthesis of Stoichiometric Titanium Carbide by a Combination of Carbothermal Reduction and Molten Salt Method and Its Characterization

Synthesis of TaB 2 -TaC nanocomposite powders by a boro-carbothermal reduction route

Molten salt synthesis of titanium carbide using different carbon sources as templates

Tuning structure, mechanical properties, and oxidation resistance of (Nb, Ta)C1- solid solution powders via the dissolution-precipitation process

Facile Electrochemical Preparation of Nano-sized Ultra-high-temperature Ta1-xHfxC Ceramic Powders

Study of the synthetic process of CaBi2Ta2O9 powder by the molten‐salt method

Electrolytic synthesis of TiC/SiC nanocomposites from high titanium slag in molten salt

Synthesis of Nano Sized Cr2AlC Powders by Molten Salt Method

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Li‐, Sb‐ and Ta‐modified (K, Na)NbO3 Nanopowder Prepared Via a Water‐based Sol–gel Method

An efficient salt-thermo-carburizing method to prepare titanium carbide coating

Exploring the impact of pH and temperature on TiC nanopowders syntesized via sol-gel and subsequent crystallization by carbothermal reduction method

A Generic Bamboo-Based Carbothermal Method For Preparing Carbide (Sic, B4c, Tic, Tac, Nbc, Tixnb1-Xc, And Taxnb1-Xc) Nanowires

Synthesis and Sintering of Tungsten and Titanium Carbide: A Parametric Study

Synthesis of niobium(iv) carbide nanoparticles via an alkali-molten-method at a spatially-limited surface of mesoporous carbon

Study on influencing factors and mechanism of high-quality tungsten carbide nanopowders synthesized via carbothermal reduction

Preparation and Characterization of TiB2/Al3Ti/Al2O3 Composite Nano-powder

Molten-salt Synthesis of BaTiO3 Powders and Their Atomic-Scale Structural Characterization