Evaluating Airflow Sensor Methods: Precision in Indirect Calorimetry

Praneel Titheradge,Robert Robergs

DOI: https://doi.org/10.1111/sms.14674

2024-06-21

Scandinavian Journal of Medicine and Science in Sports

Abstract:Scandinavian Journal of Medicine &Science in Sports, Volume 34, Issue 6, June 2024.

sport sciences

What problem does this paper attempt to address?

A combined application of tunable diode laser absorption spectroscopy and isothermal micro-calorimetry for calorespirometric analysis

David Brueckner,Anna Solokhina,Stephan Krähenbühl,Olivier Braissant

DOI: https://doi.org/10.1016/j.mimet.2017.06.012

Abstract:Calorespirometry is the simultaneous analysis of the rate of heat emission (Rq), O2 consumption (RO2) and CO2 production (RCO2) by living systems such as tissues or organism cultures. The analysis provides useful knowledge about thermodynamic parameters relevant for e.g. biotechnology where parameter based yield maximization (fermentation) is relevant. The determination of metabolism related heat emission is easy and normally done by a calorimeter. However, measuring the amount of consumed O2 and produced CO2 can be more challenging, as additional preparation or instrumentation might be needed. Therefore, tunable diode laser absorption spectroscopy (TDLAS) was investigated as an alternative approach for respirometric analysis in order to facilitate the data collection procedure. The method determines by a spectroscopic laser non-invasively CO2 and O2 gas concentration changes in the respective vial headspaces. The gathered growth data from Pseudomonas aeruginosa cultured in two different scarce media was used to compute respiratory quotient (RQ) and calorespirometric ratios (CRCO2 [Rq/RCO2], CRO2 [Rq/RO2]). A comparison of the computed (experimental) values (for RQ, CRCO2 and CRO2) with values reported in the literature confirmed the appropriateness of TDLAS in calorespirometric studies. Thus, it could be demonstrated that TDLAS is a well-performing and convenient way to evaluate non-invasively respiratory rates during calorespirometric studies. Therefore, the technique is definitively worth to be investigated further for its potential use in research and in diverse productive environments.
Comparison between Direct and Indirect Heat Flux Measurement Techniques: Preliminary Laboratory Tests

Luca Evangelisti,Leone Barbaro,Claudia Guattari,Edoardo De Cristo,Roberto De Lieto Vollaro,Francesco Asdrubali

DOI: https://doi.org/10.3390/en17122961

IF: 3.2

2024-06-17

Energies

Abstract:Direct and indirect approaches can be employed for estimating the heat flow through components in different application fields. In the building sector, the thermometric method is often applied by professionals for thermal transmittance evaluations. However, miscalculations can derive from inaccurate total heat transfer coefficients, and a consensus regarding the appropriate value to employ remains to be determined. Here, an apparatus was realized for laboratory tests and heat flux measurements were performed following direct and indirect approaches. Data acquired through a common heat flow sensor were compared with those computed through a post-processing based on radiative and convective estimations. The results were affected by the specific correlation adopted for computing the convective coefficients, with the percentage differences ranging from −9.8% to −0.4%. New measurement systems could be designed for automatically computing heat fluxes through indirect approaches, thus providing alternative solutions in the panorama of non-destructive tests for building energy diagnosis.

energy & fuels
Non-Silicon MEMS Calorimetric Gas Flow Sensor

Xuanyi Duan,Xin Fu,Haft Xie,Huayong Yang

DOI: https://doi.org/10.1109/nems.2006.334867

2006-01-01

Abstract:A novel non-silicon MEMS calorimetric gas flow sensor is presented. The sensor consists of a metal sensing/heating array placed over a glass substrate and a polyimide layer for passivation. Both the anti-pressure and anti- impact performance is enhanced by using a glass solid substrate instead of a common silicon suspending structure. This merit widens the application range of micro calorimetric sensors from millimeter- or sub-millimeter-tubes to industrial 50 mm-tubes. Both the three-element calorimetric mode and the two-element calorimetric mode were operated and calibrated on an industrial gas calibration system. It is shown that the measuring range of the prototype reaches up to 0-37.5 m3/h. Both Characteristics and optimization methods of the two calorimetric modes are discussed respectively and comparison of the two calorimetric modes is also included.
Indirect Calorimetry: History, Technology, and Application

Haifa Mtaweh,Lori Tuira,Alejandro A. Floh,Christopher S. Parshuram

DOI: https://doi.org/10.3389/fped.2018.00257

IF: 3.569

2018-09-19

Frontiers in Pediatrics

Abstract:Measurement of energy expenditure is important in order to determine basal metabolic rate and inform energy prescription provided. Indirect calorimetry is the reference standard and clinically recommended means to measure energy expenditure. This article reviews the historical development, technical, and logistic challenges of indirect calorimetry measurement, and provides case examples for practicing clinicians. Formulae to estimate energy expenditure are highly inaccurate and reinforce the role of the indirect calorimetry and the importance of understanding the strength and limitation of the method and its application.

pediatrics
Microscale, Bendable Thermoreflectance Sensor for Local Measurements of the Thermal Effusivity of Biological Fluids and Tissues.

Xu Xie,Zhu Diao,David G. Cahill

DOI: https://doi.org/10.1063/1.5141376

2020-01-01

Abstract:Measurements of the thermal transport properties of biological fluids and tissues are important for biomedical applications such as thermal diagnostics and thermal therapeutics. Here, we describe a microscale thermoreflectance sensor to measure the thermal effusivity of fluids and biological samples in a minimally invasive manner. The sensor is based on ultrafast optical pump-probe techniques and employs a metal-coated optical fiber as both a photonic waveguide and a local probe. Calibration of the sensor with five liquids shows that the percentage deviation between experimentally measured effusivity and literature values is on average <3%. We further demonstrate the capability of the sensor by measuring the thermal effusivity of vegetable oil, butter, pork liver, and quail egg white and yolk. We relate the thermal effusivity of the samples to their composition and water content, and establish our technique as a powerful and flexible method for studying the local thermal transport properties of biological materials.
An Improvement of the Method for Calibrating Measurements of Photosynthetic Co2 Flux

P Hari,P Keronen,J Back,N Altimir,T Linkosalo,T Pohja,M Kulmala,T Vesala

DOI: https://doi.org/10.1046/j.1365-3040.1999.00478.x

1999-01-01

Abstract:Measurements of rapid changes in concentrations and fluxes of gaseous compounds relating to photosynthetic gas exchange are commonly performed using flow-through cuvettes in connection,vith infrared gas analysers. The accuracy and repeatability of these measurements relies ultimately upon the design of the system as a whole, rather than upon each of its components, and therefore the calibration and testing of the system should be performed keeping this in mind. We present here a simple and efficient method for the calibration of such a measurement system using a precisely determined CO2 flow. This method gives us the opportunity to take into account any disturbing effects caused by undesired properties of the chamber or tubing materials, With the proposed calibration method, the accuracy of the CO2 flux measurement is improved from 8% up to the level of 2%, determined mainly by the accuracy of the control gas used for calibration of the CO2 analyser.
Correction to Accuracy of respiratory gas variables, substrate, and energy use from 15 CPET systems during simulated and human exercise

DOI: https://doi.org/10.1111/sms.14607

2024-03-21

Scandinavian Journal of Medicine and Science in Sports

Abstract:Scandinavian Journal of Medicine &Science in Sports, Volume 34, Issue 3, March 2024.

sport sciences
A computer-controlled indirect calorimeter for the measurement of energy expenditure in one or two subjects simultaneously

J S Garrow,J D Webster

Abstract:An indirect calorimeter is described with which it is possible to make recordings of oxygen uptake, carbon dioxide production and respiratory quotient in one or two subjects simultaneously. The gas analysers sample expired air from the two patients and room air in a continuous cycle which lasts 15 min; a microcomputer is used to switch solenoid valves, read the gas analysers and output the results to a printer. A butane lamp is described which is made from components of a camping cooker. This can be used to simulate two patients, and enables the operator to check the function of the calorimeter quickly and inexpensively. If there is an error in the system the printout indicates whether the fault is likely to be a leak or an error in a gas analyser.
Analytical Analysis of Factors Affecting the Accuracy of a Dual-Heat Flux Core Body Temperature Sensor

Jakub Żmigrodzki,Szymon Cygan,Jan Łusakowski,Patryk Lamprecht

DOI: https://doi.org/10.3390/s24061887

IF: 3.9

2024-03-15

Sensors

Abstract:Non-invasive core body temperature (CBT) measurements using temperature and heat-flux have become popular in health, sports, work safety, and general well-being applications. This research aimed to evaluate two commonly used sensor designs: those that combine heat flux and temperature sensors, and those with four temperature sensors. We used analytical methods, particularly uncertainty analysis calculus and Monte Carlo simulations, to analyse measurement accuracy, which depends on the accuracy of the temperature and flux sensors, mechanical construction parameters (such as heat transfer coefficient), ambient air temperature, and CBT values. The results show the relationship between the accuracy of each measurement method variant and various sensor parameters, indicating their suitability for different scenarios. All measurement variants showed unstable behaviour around the point where ambient temperature equals CBT. The ratio of the heat transfer coefficients of the dual-heat flux (DHF) sensor's channels impacts the CBT estimation uncertainty. An analysis of the individual components of uncertainty in CBT estimates reveals that the accuracy of temperature sensors significantly impacts the overall uncertainty of the CBT measurement. We also calculated the theoretical limits of measurement uncertainty, which varied depending on the method variant and could be as low as 0.05 °C.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Principles of indirect measurement temperature

Karol Kostúr,Karol Kostur

DOI: https://doi.org/10.1109/carpathiancc.2012.6228664

2012-05-01

Abstract:In many cases, direct measurement of temperatures in heating furnaces is impossible from various real reasons. Indirect measurement is one way for obtaining this important variable for a feedback control system. Generally, the classification of system for indirect measurement and the comparing of an uncertainty for direct and indirect measurement will be given in the paper. Principles of indirect measurement based on mathematical models will be describing including boundary conditions for their solution. Very important is the measuring precision and therefore will be given one way based on adaption of simulation model including its verification.
Distributed Flow Calorimetry With Wide Temperature and Pressure Range Based on Scanning Radiation Thermometry

Peizhao Liang,Tao Zhang,Dexin Hou,Yiming Lv,Tiancheng Xie,Jiong Ding

DOI: https://doi.org/10.1109/tim.2024.3458072

IF: 5.6

2024-09-27

IEEE Transactions on Instrumentation and Measurement

Abstract:Hydrocarbon fuels play a crucial role in addressing excessive body temperatures experienced by hypersonic vehicles during high Mach number operations, serving both as propellants and coolants. Flow calorimeters measure fluid thermodynamic parameters. Traditional ones rely heavily on thermocouples for temperature measurement, leading to a black-box effect on thermodynamic parameter analysis. To solve these problems, a distributed flow calorimetry based on scanning radiation thermometry is proposed innovatively. The analysis object is transformed from the whole tube to the microelement. The heat balance equation for the microelement and the mapping relationship between tube coordinates, tube temperature, and fluid thermodynamic parameters have been established. The feasibility of the mathematical model of fluid temperature and distributed flow calorimetry is verified by numerical simulation. Experimental data from the National Institute of Standards and Technology are compared for the distributed specific heat capacities of water and n-decane over wide temperature ranges. Between temperatures of 296.43 and 564.45 K, water's distributed specific heat capacity shows a relative error ranging from −7.42% to 8.04%, with a mean deviation of −0.72%. For temperatures spanning 298.97–601.77 K, n-decane's distributed specific heat capacity exhibits a relative error from −5.13% to 5.57%, with a mean deviation of −0.31%. The results demonstrate that distributed flow calorimetry holds promising prospects for measuring the changes in thermodynamic parameters of fluids during heat exchange.

engineering, electrical & electronic,instruments & instrumentation
Determining cold strain in cold air: a comparison of two methods of partitional calorimetry to calculate heat storage and debt in cold air with mild hypothermia

Phillip J Wallace,Geoffrey L Hartley,Stephen S Cheung

DOI: https://doi.org/10.1139/apnm-2024-0204

2024-08-14

Abstract:We compared two methods of partitional calorimetry to calculate heat storage and heat debt during cold air (0°C) exposure causing mild core cooling. Twelve participants performed a 5 min baseline in thermoneutral conditions (∼22.0°C, ∼50% relative humidity) followed by cold air exposure (∼0°C) until rectal temperature was reduced by ∆-0.5°C. Partitional calorimetry was used to calculate avenues of heat exchange (radiative, convective, and evaporative), heat storage, and heat debt continuously throughout cold exposure. We compared deriving these variables using prediction equations based on environmental and participant characteristics (PCALEquation Method) versus using measurement tools such as humidity sensors and heat flux discs (PCALHeat Flux Method). There were significant differences between methods (all p ≤ 0.001) for determining heat exchange, heat storage, and heat debt. At ∆-0.5°C, PCALHeat Flux Method had greater levels of radiative and convective heat exchange (PCALHeat Flux Method: -143.0 ± 16.8 W∙m2 vs PCALEquation Method: -123.0 ± 12.9 W∙m2, p ≤ 0.001), evaporative heat exchange (PCALHeat Flux Method: -9.0 ± 1.7 W∙m2 vs PCALEquation Method: -4.1 ± 0.0 W∙m2, p ≤ 0.001), heat storage (PCALHeat Flux Method: -15.0 ± 31.0 W∙m2 vs PCALEquation Method: +6.0 ± 25.9 W∙m2, p = 0.020), and heat debt (PCALHeat Flux Method: -692.0 ± 315.0 kJ vs PCALEquation Method: -422.0 ± 136.0 kJ, p ≤ 0.001). Overall, this study found the largest discrepancies between the two methods were when the environmental conditions and skin temperature were in high flux, as well as when core temperature was reduced by ∆-0.5°C. The use of PCALHeat Flux Method may be more advantageous to use in the cold to provide a higher resolution measurement of cold strain.
Indirect Method Versus Direct Method for Measuring Ventilation Rates in Naturally Ventilated Dairy Houses

Xiang Wang,Pius M. Ndegwa,HungSoo Joo,George M. Neerackal,Claudio O. Stockle,Heping Liu,Joseph H. Harrison

DOI: https://doi.org/10.1016/j.biosystemseng.2016.01.010

IF: 5.002

2016-01-01

Biosystems Engineering

Abstract:Indirect methods are widely used for determining air exchange rates (AER) in naturally ventilated barns because they are relatively easier and cheaper than direct methods, which measure actual airflow in and out of the barns. The main goal of this study was to evaluate a common indirect method (CO2 mass balance) against a direct method, and identify factors influencing this indirect method. The mean AER based on 24-h averaging, irrespective of method, ranged from 13 to 39 h(-1) during the study-periods. The CO2-balance method tended to overestimate barn AER. The cows' CO2 production rate, in the current study, was estimated at 0.178 m(3) h(-1) hpu(-1) based on 24-h averaging. The CO2-balance method with 24-h data averaging yielded more reliable barn AER than with shorter averaging times (i.e., 1, 2, and 12 h). The 1-h averaging, however, was chosen to analyze the effects of other pertinent factors on the CO2-balance method to capture diurnal variations of AER. Both wind speed and wind direction had significant effects on barn AER as well as the difference between the CO2-balance method and direct method. Barn AER, in general, increased with wind speed. The CO2-balance method was unreliable during milking times, and when indoor outdoor CO2 concentration and temperature differences were less than 70 ppm and 0 degrees C, respectively. (C) 2016 IAgrE. Published by Elsevier Ltd. All rights reserved.
Development of an Energy-Efficient and Highly Sensitive Thermal Microsensor for Measuring Flow Rates of Fluids

Diego Fernando Valencia-Grisales,Claudia Reyes-Betanzo

DOI: https://doi.org/10.1109/mim.2024.10473014

2024-03-19

IEEE Instrumentation and Measurement Magazine

Abstract:A calorimetric-based thermal sensor is precisely designed to measure volumetric flow rates in water, air, and nitrogen. Extensive simulations of the sensor's performance are conducted using COMSOL Multi-physics® software. In order to validate the simulation results, a comprehensive comparative analysis is carried out, utilizing the well-established one-dimensional model proposed by Nguyen and Dötzel, The sensor's construction incorporates high-quality materials such as titanium, phosphorus-doped amorphous hydrogenated silicon carbide (P-doped a-SiC:H), aluminum, and borosilicate glass substrates, ensuring robustness and reliability. The measurement range investigated spans from the flow rates of to for water, while for air and nitrogen, a broader range of 0 ml/min to 187 ml/min is considered. The evaluation of results showcases a low power consumption of approximately 7.6 mW, underlining the sensor's energy efficiency. Furthermore, the sensor exhibits remarkable sensitivities, with values reaching 54.89 mV/(mm/s)/mW for water flow and 8.9 mV/(m/s)/mW for gases, underscoring its exceptional performance across various applications.

engineering, electrical & electronic,instruments & instrumentation
Monitoring of O2 Uptake and CO2 Elimination During Anesthesia and Surgery

Peter H. Breen,Abraham Rosenbaum

DOI: https://doi.org/10.1007/978-1-4614-8557-5_37

2013-11-08

Abstract:Indirect calorimetry, the measurement of pulmonary oxygen uptake (V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$) and carbon dioxide elimination (V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$), is used extensively in the critical care medicine unit and in exercise physiology testing. However, in anesthesia, metabolic monitoring is mostly confined to the inspired oxygen fraction (to preclude the delivery of hypoxic gas mixture) and to tidal PCO2$$ {P}_{{\mathrm{CO}}_2} $$ monitoring (to ensure a patent airway and to estimate the alveolar PCO2$$ {P}_{{\mathrm{CO}}_2} $$ during mechanical ventilation). The main reason, we believe, for the lack of understanding of metabolic monitoring during anesthesia is that the measurements of V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$ are challenging in the rebreathing anesthesia circle circuit and there are few accurate measurement devices. In this chapter, we describe the development and implementation of the bymixer, an in-line flow-averaging hydraulic gas mixer, and the fast response humidity and temperature airway sensor. Along with a fast response and accurate airway flow sensor, we have demonstrated accurate and precise bymixer-flow measurements of the V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$ during extensive validations with a metabolic lung simulator. We believe that there are at least three main areas of clinical interest for the measurements of airway V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$ during anesthesia and surgery: First, there are many acute perturbations during anesthesia and surgery that can be quickly and noninvasively detected and diagnosed by non-steady-state changes in airway V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$. Second, we hypothesize that indirect calorimetry can first detect onset of anaerobic lactic acidosis during anesthesia and surgery. Third, we predict that airway V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$ will be directly affected by the level of anesthesia depth. We plan to test the hypothesis that indirect calorimetry measurements of airway V˙O2$$ {\dot{V}}_{{\mathrm{O}}_2} $$ and V˙CO2$$ {\dot{V}}_{{\mathrm{CO}}_2} $$ will help diagnose and drive treatment of these pathophysiology perturbations and improve patient outcome.
Investigation of Calibration Methodology Using Mouth Airflow for Wearable Sensor Toward Quantitative Respiration Monitoring

Kenta Horie,Muhammad Salman Al Farisi,Yoshihiro Hasegawa,Miyoko Matsushima,Tsutomu Kawabe,Mitsuhiro Shikida

DOI: https://doi.org/10.1002/tee.24045

IF: 0.923

2024-03-05

IEEJ Transactions on Electrical and Electronic Engineering

Abstract:Present wearable sensors are able to measure the frequency of vital signs such as respiration rate and heartbeat rate, but unable to measure those quantitatively, e.g. respiratory volume and heartbeat strength. Meanwhile, airflow at mouth contains both the respiration and the heartbeat quantitative signals. In this study, we propose a calibration method for a wearable vital sensor attached on the chest using the airflow at the mouth for quantitative respiration monitoring. An artificial ventilator and an experimental animal were introduced as test benches prior to human clinical experiment. As a proof of concept, a micro‐electro mechanical systems (MEMS) airflow sensor and a wearable accelerometer were implemented to both the test benches. The velocity output of the piston motion measured by the wearable sensor conformed with the airflow rate output, and the obtained results indicated that the wearable sensor can monitor not only the frequency of vital signs but also quantitative magnitudes such as the respiratory volume. © 2024 Institute of Electrical Engineer of Japan and Wiley Periodicals LLC.

engineering, electrical & electronic
Characteristics of an optimized catheter-type thermal flow sensor for measuring reciprocating airflows in bronchial pathways

M Shikida,T Yokota,T Kawabe,T Funaki,M Matsushima,S Iwai,N Matsunaga,K Sato

DOI: https://doi.org/10.1088/0960-1317/20/12/125030

2010-11-29

Journal of Micromechanics and Microengineering

Abstract:We optimized a catheter-type thermal flow sensor to measure the reciprocating airflows in bronchial pathways. The electrical wiring in the outer tube was extracted to keep the symmetry of the temperature distribution on the heaters. First, a flexible sensor was fabricated on polyimide film with photolithography, and then the enameled wires were bonded to the contact pads on the film with anisotropic conductive film. The film sensor was finally assembled with a catheter configuration that had a diameter of 1.8 mm by applying a heat shrinkable tube. We experimentally confirmed that the sensor outputs under both forward and reverse flow conditions had the same output characteristics when a design with symmetrical heating elements was applied. The sensor outputs we obtained at a reciprocating flow frequency ranging from 1 to 3 Hz almost coincided, and they also fit that obtained under unidirectional airflow conditions. Finally, the aspirated- and inspired-air characteristics in the air passages of small laboratory animals (rats and mice) were measured. Due to our development of a flexible method of electrical wiring, we could try a new approach to intubation measurements in which the sensor was inserted into the air passage from the mouth with a fiberscope, and we confirmed that the sensor we developed was able to directly measure the breathing characteristics in air passages. Implanted measurements were also attempted in this study.

engineering, electrical & electronic,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
Indirect Calorimetry in Clinical Practice

Marta Delsoglio,Najate Achamrah,Mette M. Berger,Claude Pichard

DOI: https://doi.org/10.3390/jcm8091387

IF: 3.9

2019-09-05

Journal of Clinical Medicine

Abstract:Indirect calorimetry (IC) is considered as the gold standard to determine energy expenditure, by measuring pulmonary gas exchanges. It is a non-invasive technique that allows clinicians to personalize the prescription of nutrition support to the metabolic needs and promote a better clinical outcome. Recent technical developments allow accurate and easy IC measurements in spontaneously breathing patients as well as in those on mechanical ventilation. The implementation of IC in clinical routine should be promoted in order to optimize the cost–benefit balance of nutrition therapy. This review aims at summarizing the latest innovations of IC as well as the clinical indications, benefits, and limitations.

medicine, general & internal
Investigation on the Effective Measures for Improving the Performance of Calorimetric Microflow Sensor

Jiali Qi,Chun Shao,Wei Wu,Ruijin Wang

DOI: https://doi.org/10.3390/s23177413

IF: 3.9

2023-08-26

Sensors

Abstract:The performance of the calorimetric microflow sensor is closely related to the thermal sensing part design, including structure parameter, heater temperature, and operation environment. In this paper, several measures to enhance the performance of the calorimetric microflow sensor were proposed and further verified by numerical simulations. The results demonstrate that it is more favorable to reduce the negative impact of flow separation as the space between detectors and heater is set to be 1.6 μm so as to improve the accuracy of the sensor. With an appropriate gap, the front arranged obstacle of the upstream detector can effectively widen the measure range of the sensor, benefiting from the decrease in upstream viscous dissipation. Compared to a cantilever structure, the resonances can be effectively suppressed when the heater and detectors are designed as bridge structures. In particular, the maximum amplitude of the bridge structure is only 0.022 μm at 70 sccm, which is 53% lower than that of the cantilever structure. The optimized sensor widens the range by 14.3% and significantly increases the sensitivity at high flow rates. Moreover, the feasibility of the improved measures is also illustrated via the consistency of the trend between the simulation results and experimental ones.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Evaluation of a Thermal-Based Flow Meter for Assessment of Mobile Resting Metabolic Rate Measures.

Nai-Yuan Liu,Yue Deng,Francis Tsow,Devon Bridgeman,Xiaojun Xian,Jane J. Dean,Janet L. Wilson,Nongjian Tao,Doina Kulick,Erica Forzani

DOI: https://doi.org/10.1155/2018/9186475

IF: 2.336

2018-01-01

Journal of Sensors

Abstract:This work evaluates the use of a new flow meter to assess exhalation rate. A mobile indirect calorimeter (MIC) was designed and used to measure resting metabolic rate (RMR), which relies on the measure of O-2 consumption rate (VO2) and CO2 production rate (VCO2). The device was produced from a commercially available and well-established indirect calorimeter and implemented with a new flow meter for the purpose of this study. VO2 and VCO2 were assessed by measuring exhalation rates using the new flow meter and O-2 and CO2 concentrations in breath using the original colorimetric sensors of the indirect calorimeter. The new flow meter was based on a thermal flow meter (TFM) affixed to an orifice with a diameter of 6.8 mm used as a passage for exhaled breath from 16 subjects. The results were compared with a metabolic cart (Medical Graphics), which was connected in series to the modified device. We found that 69% of the results had more than a 10% difference between the modified MIC device and the reference instrument, suggesting that the sensitivity of the thermal flow meter changed over time, which precluded its use as a flow meter for breath flow rate measurement.

Evaluating Airflow Sensor Methods: Precision in Indirect Calorimetry

A combined application of tunable diode laser absorption spectroscopy and isothermal micro-calorimetry for calorespirometric analysis

Comparison between Direct and Indirect Heat Flux Measurement Techniques: Preliminary Laboratory Tests

Non-Silicon MEMS Calorimetric Gas Flow Sensor

Indirect Calorimetry: History, Technology, and Application

Microscale, Bendable Thermoreflectance Sensor for Local Measurements of the Thermal Effusivity of Biological Fluids and Tissues.

An Improvement of the Method for Calibrating Measurements of Photosynthetic Co2 Flux

Correction to Accuracy of respiratory gas variables, substrate, and energy use from 15 CPET systems during simulated and human exercise

A computer-controlled indirect calorimeter for the measurement of energy expenditure in one or two subjects simultaneously

Analytical Analysis of Factors Affecting the Accuracy of a Dual-Heat Flux Core Body Temperature Sensor

Principles of indirect measurement temperature

Distributed Flow Calorimetry With Wide Temperature and Pressure Range Based on Scanning Radiation Thermometry

Determining cold strain in cold air: a comparison of two methods of partitional calorimetry to calculate heat storage and debt in cold air with mild hypothermia

Indirect Method Versus Direct Method for Measuring Ventilation Rates in Naturally Ventilated Dairy Houses

Development of an Energy-Efficient and Highly Sensitive Thermal Microsensor for Measuring Flow Rates of Fluids

Monitoring of O2 Uptake and CO2 Elimination During Anesthesia and Surgery

Investigation of Calibration Methodology Using Mouth Airflow for Wearable Sensor Toward Quantitative Respiration Monitoring

Characteristics of an optimized catheter-type thermal flow sensor for measuring reciprocating airflows in bronchial pathways

Indirect Calorimetry in Clinical Practice

Investigation on the Effective Measures for Improving the Performance of Calorimetric Microflow Sensor

Evaluation of a Thermal-Based Flow Meter for Assessment of Mobile Resting Metabolic Rate Measures.