Abstract:2D field-effect transistors (FETs) fabricated with transition metal dichalcogenide (TMD) materials are a potential replacement for the silicon-based CMOS. However, the lack of advancement in p-type contact is also a key factor hindering TMD-based CMOS applications. The less investigated path towards improving electrical characteristics based on contact geometries with low contact resistance (RC) has also been established. Moreover, finding contact metals to reduce the RC is indeed one of the significant challenges in achieving the above goal. Our research provides the first comparative analysis of the three contact configurations for a WSe2 monolayer with different noble metals (Rh, Ru, and Pd) by employing ab initio density functional theory (DFT) and non-equilibrium Green's function (NEGF) methods. From the perspective of the contact topologies, the RC and minimum subthreshold slope (SSMIN) of all the conventional edge contacts are outperformed by the novel non-van der Waals (vdW) sandwich contacts. These non-vdW sandwich contacts reveal that their RC values are below 50 Ω∙μm, attributed to the narrow Schottky barrier widths (SBWs) and low Schottky barrier heights (SBHs). Not only are the RC values dramatically reduced by such novel contacts, but the SSMIN values are lower than 68 mV/dec. The new proposal offers the lowest RC and SSMIN, irrespective of the contact metals. Further considering the metal leads, the WSe2/Rh FETs based on the non-vdW sandwich contacts show a meager RC value of 33 Ω∙μm and an exceptional SSMIN of 63 mV/dec. The two calculated results present the smallest-ever values reported in our study, indicating that the non-vdW sandwich contacts with Rh leads can attain the best-case scenario. In contrast, the symmetric convex edge contacts with Pd leads cause the worst-case degradation, yielding an RC value of 213 Ω∙μm and an SSMIN value of 95 mV/dec. While all the WSe2/Ru FETs exhibit medium performances, the minimal shift in the transfer curves is interestingly advantageous to the circuit operation. Conclusively, the low-RC performances and the desirable SSMIN values are a combination of the contact geometries and metal leads. This innovation, achieved through noble metal leads in conjunction with the novel contact configurations, paves the way for a TMD-based CMOS with ultra-low RC and rapid switching speeds.

Does P-type Ohmic Contact Exist in WSe2-metal Interfaces?

Low Resistance Ohmic Contact to P-type Monolayer WSe2

Pervasive Ohmic Contacts in Bilayer Bi2O2Se–Metal Interfaces

Ohmic MXene Contacts for Symmetric P- and N-Type Monolayer WSe2 Schottky Barrier Field-Effect Transistors

Low Resistance Contact to P-Type Monolayer WSe2

Mechanistic Understanding of the Interfacial Properties of Metal-PtSe2 Contacts

A Computational Study of Monolayer Hexagonal WTe2 to Metal Interfaces

Unusual Fermi‐Level Pinning and Ohmic Contact at Monolayer Bi2O2Se–Metal Interface

Tunable Ohmic, p-Type Quasi-Ohmic, and n-Type Schottky Contacts of Monolayer SnSe with Metals

Tunable Contact Types and Interfacial Electronic Properties in TaS2/MoS2 and TaS2/WSe2 Heterostructures

Engineering Schottky-to-Ohmic contact transition for 2D metal–semiconductor junctions

P-type Ohmic contact to MoS2 via binary compound electrodes

P-type Ohmic contact to monolayer WSe2 field-effect transistors using high electron affinity amorphous MoO3

Ohmic Contacts Between Monolayer WSe2 and Two-Dimensional Titanium Carbides

Interfacial Properties of Monolayer MoSe2–Metal Contacts

Interfacial Properties of Monolayer and Bilayer MoS 2 Contacts with Metals: Beyond the Energy Band Calculations

Interfacial Properties of Monolayer and Bilayer MoS2 Contacts with Metals: Beyond the Energy Band Calculations

Junction-configuration-dependent interfacial electronic states of a monolayer MoS2/metal contact

Schottky Contact in Monolayer WS2 Field‐Effect Transistors

Impact of Rh, Ru, and Pd Leads and Contact Topologies on Performance of WSe2 FETs: A First Comparative Ab Initio Study

Electrical transport properties of atomically thin WSe2 using perpendicular magnetic anisotropy metal contacts