Abstract:This paper investigates the nonlinear chatter phenomena in cylindrical plunge grinding process. In this dynamic model analyzed here, the grinding wheel and workpiece are regarded as a damped spring mass system and a slender hinged-hinged Euler-Bernoulli beam respectively, and the regenerative interaction between the workpiece and the grinding stone is treated as the main factor that affects the stability of the grinding process. Because of the regenerative effects on the surfaces of both workpiece and grinding wheel, the current penetration depth of the grinding wheel into the workpiece is presented as the differences between the current and previous positions of grinding wheel and vice verse. Then these penetrations are transformed into regenerative force by multiplied contact stiffness. The contact stiffness, the rotation speeds of the grinding wheel and the workpiece are the key parameters involved in the regenerative force model. And the effects of the three parameters related to the regeneration on the dynamic motions of the grinding process are studied in this paper. To locate the stability boundaries in the parameter space, a continuation algorithm has been established to numerically compute the critical eigenvalues and corresponding parameters. The stability boundaries in the parameter space are obtained as the critical parameters that make the characteristic equations have one pair of pure image eigenvalues and all of the rest have negative real parts. By the obtained stability boundaries, the parameter space is divided into different regions where the grinding process is chatter or chatter free respectively. Following the linear stability analysis, the nonlinear bifurcation analyses are carried out and both supercritical and subcritical Hop bifurcations are found on one stability boundary. Then the Bautin bifurcation theory has been applied to discriminate these different dynamic phenomena, which are seemed contradictory in the former codimension-1 bifurcation analysis. These results show that the regenerative force plays a significant role in inducing chatter in grinding, and the contact stiffness is a key parameter for suppressing chatter. In most work conditions, choosing a softer grinding wheel is suggested. But when one has to grinding hard materials, such as ceramic, glass, hard steels and so on where larger contact stiffness are unavoidable, the rotation speeds of the workpiece and the grinding wheel should be chosen according to the stability analysis, or the unwanted chatter would arise. Another advice is that the parameters should be located not only in the linear stable regions but also far away from the neighborhood of subcritical Hopf bifurcation points where stable steady grinding and large amplitude chatter coexist.

Bifurcation analysis for instability detection in high-speed micromilling of thin-walled Ti6Al4V structure

Development of smart manufacturing framework for micromilling of thin-walled Ti6Al4V

Unstable Islands and Bifurcation Analysis in A Spindle Milling System Supported by Ball Bearings

Bifurcation analysis of thin-walled structures trimming process with state-dependent time delay

An efficient and precise stability analysis method for milling process

Stability Analysis of Milling Based on the Barycentric Rational Interpolation Differential Quadrature Method

Bautin Bifurcation Induced Nonlinear Chatter In Cylindrical Plunge Grinding

Investigation of Dynamic Behavior and Process Stability at Turning of Thin-Walled Tubular Workpieces Made of 42CrMo4 Steel Alloy

Modelling of the stability of variable helix end mills

Serrated Chip Formation Induced Periodic Distribution of Morphological and Physical Characteristics in Machined Surface During High-Speed Machining of Ti6Al4V

Stability analysis for milling system with variable pitch cutters under variable speed

Trochoidal milling: investigation of dynamic stability and time domain simulation in an alternative path planning strategy

Analysis of the Influence of Mill Helix Angle on Chatter Stability

Dynamics and Stability of Milling Thin Walled Pocket Structure

Sensitivity Analysis and Monte Carlo Based Uncertainty Quantification of the In-process Modal Parameters in Milling

Stability analysis and experimental research for three-dimensional dither in processing of high speed milling

Chatter suppression analysis for variable pitch cutter in milling

Numerical investigation on serrated chip formation during high-speed milling of Ti-6Al-4V alloy

A Semi-Analytical Method for Stability Analysis of Milling Thin-Walled Plate

Investigation of variable pitch tool design for chatter suppression in milling of Ti-6Al-4 V: a comparison of simulation and experimental results

Stability analysis of machine tool spindle under uncertainty