Investigation of Dynamic Behavior and Process Stability at Turning of Thin-Walled Tubular Workpieces Made of 42CrMo4 Steel Alloy

Kamel Mehdi,Peter Pavol Monka,Katarina Monkova,Zied Sahraoui,Nawel Glaa,Jakub Kascak
DOI: https://doi.org/10.3390/machines12020120
IF: 2.899
2024-02-09
Machines
Abstract:During machining, the surface of the machined materials is damaged and tool wear occurs, sometimes even to complete failure. Machining of thin-walled parts is generally cumbersome due to their low structural rigidity. The study deals with the effect of the feed rate and the thickness of the thin-walled part on the dynamic behavior and stability of the turning process during the roughing and finishing of thin-walled tubular workpieces made of steel alloy 42CrMo4. At the same time, the cutting forces and deformations of the workpiece were also evaluated via numerical and experimental approaches. The numerical study is based on a three-dimensional (3D) finite element model (FEM) developed using the ABAQUS/Explicit frame. In the model, the workpiece material is governed by the behavior law of Johnson–Cook. Numerical and experimental results show that the cutting forces and the quality of the machined surface depend not only on the choice of cutting parameters but also on the dynamic behavior of thin-walled parts due to their low rigidity and low structural damping during the machining operation. Cutting forces are proportional to the feed rate and inversely proportional to the thickness of the part. Their variations around the average values are low for roughing tests where the wall-part thickness is higher or equal to 3.5 mm. However, these variations intensify for finishing tests where the wall thickness is less or equal to 1.5 mm. Indeed, the recorded FFT spectra for a finishing operation show several harmonics that occurred at around 550 Hz, and the amplitude of the peaks, which describes the level of power contained in the signals, shows an increase similar to that of the amplitudes of the temporal signal. The flexibility of the part generates instability in the cutting process, but the frequencies of the vibrations are higher than the frequency of rotation of the part.
engineering, mechanical, electrical & electronic
What problem does this paper attempt to address?
The problem that this paper attempts to solve is the dynamic behavior and machining stability of thin - walled tubular workpieces during the turning process. Specifically, the research aims to explore the influence of feed rate and the thickness of the thin - walled part on the dynamic behavior and stability of thin - walled tubular workpieces made of 42CrMo4 steel alloy during roughing and finishing processes. In addition, the cutting force and workpiece deformation are also evaluated through numerical and experimental methods. ### Research Background and Motivation 1. **Low Stiffness and Low Structural Damping**: Due to their low stiffness and low structural damping, thin - walled parts are prone to vibration and instability during machining, resulting in problems such as poor surface quality and increased tool wear. 2. **Insufficient Existing Research**: Although the turning of 42CrMo4 steel has been extensively studied, relatively little research has been done on the dynamic behavior and stability of its thin - walled parts, especially in terms of numerical simulation. 3. **Practical Application Requirements**: Thin - walled parts widely used in industry (such as components in aerospace, automotive and other fields) have high requirements for machining accuracy and stability, so it is necessary to conduct in - depth research on their dynamic behavior and stability. ### Research Objectives 1. **Analyze Dynamic Behavior**: Through numerical simulation and experimental verification, study the dynamic behavior of thin - walled tubular workpieces during the turning process, especially the change of cutting force and its influence on machining stability. 2. **Optimize Machining Parameters**: Determine the key factors affecting the machining stability of thin - walled parts (such as feed rate, wall thickness, etc.), and provide a theoretical basis for optimizing machining parameters. 3. **Establish a Prediction Model**: Develop a numerical model based on the three - dimensional finite element method (3D FEM) to predict the cutting force and workpiece deformation under different machining conditions, so as to guide the process design in actual production. ### Main Research Contents 1. **Numerical Simulation**: - Use ABAQUS/Explicit software to build a 3D finite element model, considering the Johnson - Cook constitutive relationship of the material. - Simulate the turning process under different feed rate and wall thickness conditions, and calculate the cutting force and workpiece deformation. 2. **Experimental Verification**: - Measure the cutting force and workpiece deformation through experiments to verify the accuracy of the numerical model. - Analyze the FFT spectrum to study the vibration characteristics during the cutting process. 3. **Result Analysis**: - Explore the relationship between cutting force, feed rate and wall thickness. - Evaluate the dynamic behavior and stability of workpieces under different machining conditions and propose improvement measures. ### Conclusion Through numerical simulation and experimental research, this paper reveals the dynamic behavior and stability characteristics of thin - walled tubular workpieces during the turning process, providing a scientific basis for optimizing machining parameters. The research results show that the cutting force is not only affected by the feed rate, but also closely related to the wall thickness of the workpiece. Especially when the wall thickness is thin, the low stiffness and low damping of the workpiece will lead to greater vibration and instability. These findings are helpful to improve the machining quality and efficiency of thin - walled parts.