Abstract:Thin-walled parts are often used in various industrial applications and due to their functional requirements, higher accuracies are generally desired. But due to their low stiffness characteristics, deformation and chatter problems are frequently encountered in their machining, thus resulting in poor accuracy. Moreover, due to 5-axes milling, which is usually required for finish machining of such parts, further complexities in the process are added and, consequently, achieving higher accuracy becomes more challenging. Therefore, in this study, the influence of tool inclination angle and feeding direction has been investigated on the resultant surface accuracy of thin cantilever shaped parts in finish milling conditions through experiments, finite element method simulations and theoretical discussions. Moreover, since work material’s microstructure and hardness also have key influence on its machinability, therefore, the effect of heat treatment state on resulting surface accuracy also has been explored. Three different titanium alloy, Ti–6Al–4 V specimens have been used. Two of the specimens were given solution treatment at 1050 ℃/1 h followed by aging at 550 ℃/4 h. One of the specimens after being solution treated was allowed to cool in air while the other was cooled in water to obtain different microstructure and hardness whereas the third specimen was used in as-received condition (casted). The three Ti–6Al–4 V specimens were machined at five different tool inclination angles (60°, 70°, 75°, 80°, and 85°) with two feeding directions (horizontal inwards and vertical inwards). Results have shown that the angle near the perpendicular to the surface i.e. 85° (5° away from the perpendicular) has lowest deformation value and also has better surface quality, which shows that the lowest effective cutting speed at this angle has helped in achieving higher accuracy. Moreover, among the cutting directions studied, vertical inward direction produces smoother surface due to its less pushing effect on the surface being cut as compared to horizontal inwards direction. And in terms of heat treatment state, the specimen which was cooled in air after being solution treated has produced better results for all cutting conditions studied, mainly attributed to fine homogenous lamellar α + β Ti–6Al–4 V structure achieved due to slow cooling rate of air. Analysis of variance using response surface methodology has been carried out to develop predictive model and to study the influence of each variable on the accuracy. The developed model has shown good accuracy when validated through additional experiments.

Experimental Investigations on Surface Integrity in Thin Structure Machining of Aluminum 6061-T6

Residual stresses and surface damage when micromachining 6061-T6 aluminum alloy

Investigation of deviation and surface topography in ultrasonic vibration-assisted milling

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

CHARACTERIZATION OF SURFACE, SUBSURFACE DAMAGE AND THEIR EFFECT ON FATIGUE LIFE AFTER MACHINING OF AEROSPACE-GRADE ALUMINUM ALLOY (Al 6082-T6)

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

A Numerical Simulation of Machining 6061 Syntactic Foams Reinforced with Hollow Al2O3 Shells

Investigation on Surface Quality of a Rapidly Solidified Al-50%Si Alloy Component for Deep-Space Applications

Influence of Tools and Cutting Strategy on Milling Conditions and Quality of Horizontal Thin-Wall Structures of Titanium Alloy Ti6Al4V

A numerical investigation and experimental validation on chip morphology of Aluminum Alloy 6061 during orthogonal machining

Review of improvement of machinability and surface integrity in machining on aluminum alloys

Computational Analysis of Machining Induced Stress Distribution during Dry and Cryogenic Orthogonal Cutting of 7075 Aluminium Closed Cell Syntactic Foams

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting

Computer aided simulation and experimental investigation of the machinability of Al 6065 T6 during milling operation

Effect of Ranque-Hilsch Vortex Tube Cooling to Enhance the Surface-Topography and Tool-Wear in Sustainable Turning of Al-5.6Zn-2.5Mg-1.6Cu-0.23Cr-T6 Aerospace Alloy

Influence of Tool Inclination Angle and Cutting Direction on Long Thin-Walled Part’s Dimensional and Geometric Accuracy when High-Speed Ball End Milling the Heat-Treated Titanium Alloy Ti–6Al–4 V

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Investigation of Dynamic Behavior and Process Stability at Turning of Thin-Walled Tubular Workpieces Made of 42CrMo4 Steel Alloy

Novel Approach to Monitoring the Surface Integrity of Aluminum 5052 Using Sound and Vibration Signals during Turning with Titanium-Coated Carbide Inserts

Coupling effect of micro-textured tools and cooling conditions on the turning performance of aluminum alloy 6061

Investigation of Machining Process Parameters for Deformation Machining of AA6061 Monolithic Parts to Improve the Process Outputs