Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Computer aided simulation and experimental investigation of the machinability of Al 6065 T6 during milling operation

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Finite Element Simulation and Analysis of Aluminum Alloy Three-Dimensional Milling

Simulation of 3d Chip Shaping of Aluminum Alloy 7075 in Milling Processes

Numerical modeling and experimental assessment of dynamic behavior of aluminum alloy 7075-T6 in machining process

Milling of additively manufactured AlSi10Mg with microstructural porosity defects, finite element modeling and experimental analysis

CHARACTERIZATION OF SURFACE, SUBSURFACE DAMAGE AND THEIR EFFECT ON FATIGUE LIFE AFTER MACHINING OF AEROSPACE-GRADE ALUMINUM ALLOY (Al 6082-T6)

A Numerical Simulation of Machining 6061 Syntactic Foams Reinforced with Hollow Al2O3 Shells

A numerical investigation and experimental validation on chip morphology of Aluminum Alloy 6061 during orthogonal machining

Prediction of surface roughness and optimization of process parameters for efficient cutting of aluminum alloy

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Review of improvement of machinability and surface integrity in machining on aluminum alloys

Modeling and optimization of surface residual stress profiles in milling of aluminum 7075-T6 alloy

Experimental and 3D-Deform Finite Element Analysis on Tool Wear during Turning of Al-Si-Mg Alloy

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Multiparameter signal-to-noise ratio optimization for end milling cutting conditions of aluminium alloy 5083

An experimental study of the response characteristics of end milling operations and their finite element simulation

Comparative investigation and optimization of cutting tools performance during milling machining of titanium alloy (Ti6Al4V) using response surface methodology

Multi-Objective Optimization of Machining Parameters on Aluminium Alloy Metal Matrix Composites using Response Surface Methodology

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures