Abstract:Magnesium alloys are lightweight structural materials with excellent machinability. However, further development is seriously limited by their low strength and poor formability. Therefore, further decreasing the surface residual stress of the frame by post-process treatment is a key issue, such as for reducing the subsequent deformation due to the residual stress, improving the machining accuracy and corrosion resistance of the magnesium alloy frame products, and extending the service life of the magnesium alloy frame products. Using AZ31B magnesium alloy as the experimental subject, and by exploring the effects of milling parameters on the surface quality of frame parts, this study shows that the surface residual compressive stress, hardness, and roughness of frame parts decreased with the increasing of the milling speed and increased as the depth of cut and the feed per tooth increased. Using cutting fluid in the milling process can decrease the surface residual stress and roughness of the frame parts but increase the surface hardness. In accordance with the experimental results and analysis, the main reason affecting the residual stress on the surface layer of frame components is the thermal elastoplastic problem caused by thermal mechanical coupling during the milling process, resulting in varying stress states on the workpiece's surface. The primary contributors to hardness are the work-hardening effect induced by milling forces and the thermal-softening effect of milling temperatures, which either augment or diminish the workpiece's surface hardness. Furthermore, the primary factor impacting surface roughness is the magnitude of cutting forces. Excessive cutting forces lead to the ploughing phenomenon or tool vibrations, thereby causing varying degrees of surface roughness on the workpiece. Meanwhile, the influence of stress-relief annealing or cryogenic treatment on surface residual stress and hardness after the milling of the frame parts was researched. It shows that within the selected milling parameters, both stress-relief annealing and cryogenic treatment can reduce the surface residual stress and homogenize the residual stress distribution of frame parts. Stress-relief annealing leads to a reduction in the hardness of the machined surface, and the hardness of the machined surface increases slightly under cryogenic treatment. The effects of the two post-processing methods on surface quality vary, and in practical production, a rational selection can be made according to the different processing requirements to achieve the optimal standards.

Residual stresses and surface damage when micromachining 6061-T6 aluminum alloy

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Investigation on the damage mechanism of micro-cutting surface layer of aluminum alloy 7075 with different heat treatment processes

Effect of cutting parameters on the microstructure evolution and damage mechanism of 7075-T6 aluminum alloy in micro cutting

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Construction of a predictive model for residual stresses in micro-milling of 7075 aluminum alloy

Experimental Investigations on Surface Integrity in Thin Structure Machining of Aluminum 6061-T6

Study on the Micro-cutting Mechanism of 7075 Aluminum Alloy with Pre-fabricated Surface Microtextures

CHARACTERIZATION OF SURFACE, SUBSURFACE DAMAGE AND THEIR EFFECT ON FATIGUE LIFE AFTER MACHINING OF AEROSPACE-GRADE ALUMINUM ALLOY (Al 6082-T6)

Micro-scale measurement & FEM modelling of residual stresses in AA6082-T6 Al alloy generated by wire EDM cutting

Study on Residual Stress Produced in Milling of Aeronautic Structure

Computational Analysis of Machining Induced Stress Distribution during Dry and Cryogenic Orthogonal Cutting of 7075 Aluminium Closed Cell Syntactic Foams

Modeling and optimization of surface residual stress profiles in milling of aluminum 7075-T6 alloy

Computer aided simulation and experimental investigation of the machinability of Al 6065 T6 during milling operation

Analysis of cutting forces and surface quality during micro milling of AZ31B magnesium alloy

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

Study of Machined Surface Quality of AZ31B Magnesium Alloy by End Milling

Microstructure Evolution and Micro-nano-mechanical Properties of 6061 Aluminum Alloy in Hot Flow Forming under Different Thinning Rates

The Effect of Cutting Parameters on Surface Quality and Corrosion Resistance of Micro-machined Surfaces of 7075 Aluminum Alloy

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Quantitative evaluation of residual stress and microstructural effects on the surface hardness of machined Ti-6Al-4 V alloy with microscopic characterization techniques