Abstract:The cold rolling and intermediate annealing process, along with the incorporation of rare earth elements, play an important role in the microstructure, texture, and inhibitors of oriented silicon steel. Currently, there is limited research on the impact of rare earth yttrium on texture evolution during the cold rolling and intermediate annealing processes. Therefore, the effects of different cold rolling deformations and intermediate annealing temperatures on the microstructure and texture of Y bearing oriented silicon steel have been studied. The experimental results demonstrate that the average grain size of the intermediate annealed plate progressively decreases with increasing the cold rolling deformation. This is because the high cold rolling deformation brings more additional dislocations and distortions, consequently enhancing the driving force for recrystallization. Observing the microstructure with various cold rolling deformation, the results show that the annealed plate with a 72 % reduction rate exhibited the highest Goss texture percentage of 4.83 %. This is because the cold-rolled sheet with a reduction rate of 72 % exhibits an abundance of Goss oriented substructures. These substructures quickly dominate the {111} deformed matrix during the initial recrystallization, and promote grains nucleation and growth. As the annealing temperature increases, the driving force for the growth of recrystallized grains also increases, leading to a gradual increase in grain size. The plate annealed at 940 °C exhibits the highest percentage (4.83 %) of Goss texture. The addition of rare earth Y can lead to an increase in grain size in the intermediate annealed plate and facilitate the formation of {411} texture. This is advantageous for the abnormal growth of Goss texture. The results demonstrate that a cold rolling deformation rate of 72 % and an intermediate annealing temperature of 940 °C are good for promoting abnormal growth of Goss orientation. The study results on precipitation kinetics suggests that the grain boundary nucleation of AlN and dislocation nucleation of MnS are the most effective way of nucleation. The precipitates in oriented silicon steel without Y are Al 2 O 3 and MnS, while those in the samples with Y are AlN, YS, and YO x S y . The addition of rare earth Y leads to a reduction in both the density and size of precipitates. Moreover, With the increase of annealing temperature, the size of precipitates decreases and the amount of precipitates increases. Additionally, the addition of Y makes the steel more clean, meanwhile, the pinning effect of inclusions on grain boundaries is weakened. Therefore, the grain size of the steel with Y is larger.

Microstructure and texture transformation of unidirectional rolled 3% Y 2 O 3p /ZGK200 composites during annealing

Tailoring the texture and mechanical properties of 3% Y 2 O 3p /ZGK200 composites fabricated by unidirectional and cross rolling followed by annealing

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Effect of intermediate annealing temperature and cold rolling deformation on the texture of yttrium bearing oriented silicon steel

Evolution of microstructure and texture of moderately warm-rolled pure tungsten during annealing at 1300 °C

Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200 °C and 1350 °C

Orientation relationship of texture development in hot-rolled W during annealing

Microstructure and Annealing Behavior of Three Rolled Pure Tungsten Plates with Different Thickness Reduction

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

The Influence of Annealing on the Microstructural and Textural Evolution of Cold-Rolled Er Metal

Restoration kinetics and microstructural evolution of moderately warm-rolled yttria dispersion-strengthened tungsten plate during annealing at high temperatures

Microstructure and texture of coarse-grained Mg-Gd-Y-Nd-Zr alloy after hot compression

Intermediate Annealing of Warm-rolled Sheets and Its Influence on the Texture Evolution in the Rolled Columnar-grained Fe-Ga Alloys

Recrystallization and Texture Evolution of Cold-Rolled AZ31 Mg Alloy Treated by Rapid Thermal Annealing

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Effect of recovery annealing prior to recrystallization annealing on the texture evolution of a 3.3% silicon steel