Abstract:Slicing and post-treatment of SiC crystals have been a significant challenge in the integrated circuit and microelectronics industry. To compete with wire-sawing and mechanical grinding technology, a promising approach combining laser slicing and laser polishing technologies has been innovatively applied to increase utilization and decrease damage defects for single crystal 4H-SiC. Significant material utilization has been achieved in the hybrid laser processes, where material loss is reduced by 75% compared to that of conventional machining technologies. Without any special process control or additional treatment, an internally modified layer formed by laser slicing can easily separate the 4H-SiC crystals using an external force of about similar to 3.6 MPa. The modified layer has been characterized using a micro-Raman method to determine residual stress. The sliced surface exhibits a combination of smooth and coarse appearances around the fluvial morphology, with an average surface roughness of over Sa 0.89 pm. An amorphous phase surrounds the SiC substrate, with two dimensions of lattice spacing, d = 0.261 nm and d = 0.265 nm, confirmed by high-resolution transmission electron microscopy (HRTEM). The creation of laser-induced periodic surface nanostructures in the laser-polished surface results in a flatter surface with an average roughness of less than Sa 0.22 pm. Due to the extreme cooling rates and multiple thermal cycles, dissociation of Si-C bonding, and phase separation are identified on the laser-polished surface, which is much better than that of the machining surface. We anticipate that this approach will be applicable to other high-value crystals and will have promising viability in the aerospace and semiconductor industries.(c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Advancements in single-crystal silicon with elevated-laser-liquid-phase-epitaxy (ELLPE) for monolithic 3D ICs

Single-Crystal Islands (SCI) for Monolithic 3-D and Back-End-of-Line FinFET Circuits

Recent Advances in Monolithic Integration of Diverse Technologies with Si CMOS

Monolithic Three‐dimensional Integration of Aligned Carbon Nanotube Transistors for High‐performance Integrated Circuits

High Performance Junctionless FDSOI SiGe Channel P-Finfet with High ION/IOFF Ratio and Excellent SS

Seamless monolithic three-dimensional integration of single-crystalline films by growth

High-Quality Recrystallization of Amorphous Silicon on Si (100) Induced via Laser Annealing at the Nanoscale

Monolithic 3D integration of back-end compatible 2D material FET on Si FinFET

Fabricating 3D Si nanostructure via a novel Ga+ implantation enabled maskless dry etching process

Post-CMOS Process for High-Aspect-ratio Monolithically Integrated Single Crystal Silicon Microstructures

Electrochemical etching strategy for shaping monolithic 3D structures from 4H-SiC wafers

3D Electronics: 3D Sidewall Integration of Ultrahigh‐Density Silicon Nanowires for Stacked Channel Electronics (adv. Electron. Mater. 7/2019)

Mono 3 D to Develop Large-Scale Monolithic 3 D Integrated Circuits

Toward monolithic growth integration of nanowire electronics in 3D architecture: a review

Fabrication of Low Cost and Low Temperature Poly-Silicon Nanowire Sensor Arrays for Monolithic Three-Dimensional Integrated Circuits Applications

Surface Micromorphology and Nanostructures Evolution in Hybrid Laser Processes of Slicing and Polishing Single Crystal 4H-Sic

Advances in Materials and Junction Engineering Enabled by Epi

Monolithic three-dimensional integration of complementary two-dimensional field-effect transistors

Three-Dimensional Stacked-Fin-Cmos Integrated Circuit Using Double Layer Soi Material

Van der Waals Epitaxial Growth of Ultrathin Indium Antimonide on Arbitrary Substrates Through Low‐thermal Budget

Low‐temperature SOI SiGe/Si superlattice FinFET with omega‐shaped channel and self‐allied silicide for 3D sequential IC