Abstract:Due to the high modulus, high strength, low density, excellent wear resistance and good neutron absorption, the boron carbide (B4C) particle reinforced aluminum (Al) matrix composites have been widely applied in the aerospace, weaponry, transportation and neutron shielding fields. In response to the increasing requirement of better strength -ductility matching of B4C/Al composites, introducing a nano-scale reinforcement into the B4C/Al composites becomes an attractive research focus. In this work, the SiC nanowires were ball-milled with Al powders, and then the SiC/Al composite powders were mixed with B4C microparticles. Thus, the 15vol. % B4C/SiC/Al composites with different volume fractions of SiC nanowires were fabricated by hot-pressing sintering and hot extrusion. B4C microparticles and SiC nanowires are uniformly dispersed in the B4C/SiC/Al composites, while the introduced SiC nanowires effectively decrease the Al matrix grain sizes. B4C/SiC/Al composites produce the better strength-ductility matching than that of B4C/Al composites, while the 15vol. % B4C/SiC/Al composite with 1vol. % SiC nanowires achieved the best strength-ductility matching. It generates the 281.7 ± 2.7 MPa in yield strength, 351.2 ± 0.1 MPa in ultimate tensile strength and 5.9 ± 0.7% in failure elongation, which are increased by 18.2%, 15.1% and 13.5% compared to the B4C/Al composites. Uniformly dispersed B4C microparticles and SiC nanowires largely block the dislocation motions and improve the dislocation storage capacity, which results in a more significant hetero-deformation induced (HDI) hardening effect in the B4C/SiC/Al composites. Moreover, the B4C/Al interfacial transition regions with the added SiC nanowires becomes stronger, which can enhance the load transfer efficiency of the B4C/Al interfaces as a result of the existing dislocation hardening zones. In conclusion, it is a good strategy to combine the synergistic strengthening effect of micro-scale and nano-scale reinforcements in the metal matrix composites.

Influence of the Reinforcement Phase Composition on the Structure and Abrasive Wear Resistance of Aluminum Matrix Composites Reinforced with B4C and SiC

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Fabrication, microstructure characterization and mechanical properties of B4C microparticles and SiC nanowires hybrid reinforced aluminum matrix composites

Adhesive wear behaviour of B4C and SiC reinforced 4147 Al matrix composites (Al/B4C–Al/SiC)

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Dry sliding friction and wear properties of B4C particulate-reinforced Al-5083 matrix composites

Abrasive Wear Behavior of AZ31−B4C Composites

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Effect of reinforced aluminium alloy LM30 with pure ceramic particles to evaluate hardness and wear properties

Processing and Evaluation of Mechanical Properties and Dry Sliding Wear Behavior of AA6061-B4C Composites

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Dry Sliding Wear Studies on Sillimanite and B4C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process

Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite

Preparation of B4Cp/Al Composites via Selective Laser Melting and Their Tribological Properties

Abrasive Wear Behaviour of Sand Cast B4C Particulate Reinforced AA5052 Metal Matrix Composite

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites