Abstract:This paper presents the results of studies to understand the influence of hybridisation on mechanical and tribological behaviour as well as dry sliding wear of aluminium metal matrix composites. Sillimanite and boron carbide (B4C) were used as primary and secondary reinforcements and pure aluminium was used as the matrix material. The composite was fabricated by using a vacuum assisted stir casting process. Different research instruments were used, including a scanning electron microscope with EDX spectrometer, a surface measurement device, a thermal image analyser, as well as a tribotester. The results show that tensile, impact strength and hardness of the hybridised composites are superior (a step ahead) than unreinforced and primary composites. The wear behaviour of the fabricated specimens was tested for the dry sliding wear behaviour under the load range of 10-50 N with the steps of 20 N for the sliding velocities 0.75, 1.5 and 2.25 m/s over a distance of 1000 m. The wear rate increased with load and decreased as the wt.% of reinforcement increased. The wear rate of the composite with 10 wt.% Al2SiO5 was approximately 44% lower than that of the composite with 5 wt.% Al2SiO5. The same dependence was noted for hybrid composite (5 wt.% Al2SiO5 + 5 wt.% B4C)-the wear rate was approximately 50.8% lower than that of the composite with 5 wt.% Al2SiO5 under the same test condition. The friction coefficient decreased as the weight percentage of the reinforcement (Al2SiO5 and B4C) increased due to the uniform distribution of the reinforcement on the surface of the composites. The main wear mechanism of the studied materials was abrasion wear. The wear mechanism of the composite had tribochemical type. It involved the oxidation and transfer of the material, which formed protective tribolayers ensuring an additional sliding process. The mechanism that played the main role in the wear process of the composites was a combination of abrasive, adhesive and oxidative wear.

Dry sliding friction and wear properties of B4C particulate-reinforced Al-5083 matrix composites

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Processing and Evaluation of Mechanical Properties and Dry Sliding Wear Behavior of AA6061-B4C Composites

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Modeling of wear performance and surface roughness of AA6061-T6/B4C composite under dry sliding conditions by RSM

Study on the friction drilling behaviors and tribological properties of aluminum matrix composites

Influence of the Reinforcement Phase Composition on the Structure and Abrasive Wear Resistance of Aluminum Matrix Composites Reinforced with B4C and SiC

Preparation of B4Cp/Al Composites via Selective Laser Melting and Their Tribological Properties

Abrasive Wear Behavior of AZ31−B4C Composites

Wear and friction behaviour of Cu-Gr-B4C composites and correlating to the topographical characteristics

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Contributions of the Particulate Reinforcement to Dry Sliding Wear Resistance of Rapidly Solidified Al-Ti Alloys

Mechanical and tribological property of Cu/CrB 2 composites under dry sliding condition

Adhesive wear behaviour of B4C and SiC reinforced 4147 Al matrix composites (Al/B4C–Al/SiC)

Abrasive Wear Behaviour of Sand Cast B4C Particulate Reinforced AA5052 Metal Matrix Composite

Dry Sliding Wear Studies on Sillimanite and B4C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process

Development and Tribological Investigation of B4C Reinforced AA5082 Aluminum Alloy Cast Composites for Automotive Applications

Tribological Behaviour of Al18B4O33-whisker-reinforced Hypoeutectic Al–Si–Mg-matrix Composites under Dry Sliding Conditions

Effect of TiC-particle Size on Sliding Wear of TiC Particulate Reinforced Alumina Composites

Through-thickness particle distribution, microstructure evolution and tribological performance of B 4 C/BN-AA6061 composite via friction stir processing