Abstract:The metal matrix composites (MMCs) especially aluminum-based composites have made greater impact in automobile and aerospace industries in view of possessing inherent properties, such as lower density, higher stiffness, good wear resistance and reduced friction levels. These are achieved through the introduction of different types of reinforcements/fillers in the matrix to achieve tailor-made properties. The various ceramic reinforcements like alumina, silicon carbide, zirconia, graphite, molybdenum di-sulfide, fly ash, etc., have contributed to the enhancement in the properties. For example, the graphite addition to a matrix improves the wear resistance and lowers the friction levels because of its self-lubricity effect. The adoption of other types of reinforcements/fillers such as silicon carbide, silica, alumina, Beryl, and aluminide in the matrix has yielded higher hardness and lower wear losses. A lot of efforts have gone in by various researchers to prove the beneficial effect of adding Beryl particles at different levels to the aluminum matrix, and the results are quite encouraging. In this context, the tribological response of MMCs consisting of aluminum 2024 (Al2024) matrix together with Beryl particles as reinforcements produced by stir casting technique has been studied in detail as Beryl is a hard substance and favors wear resistance and coefficient of friction. The wear and friction tests have been conducted using a Pin-On-Disc (POD) test setup, and the load employed is in the range 49 to 136 N with a sliding speed of 320 rpm. The information on this is infrequent to come across especially the aspect of the higher load applications in POD. Further, the worn-out surface features due to the sliding action have been examined and assessed using scanning electron microscopy (SEM). Recourse of supporting tests such as X-ray diffraction, hardness, noting of surface roughness and light microscopy has been resorted to substantiate the results. It is observed from the data there is a drop in wear loss of about 1.8 to 2.2 times and coefficient of friction reduced by about 1.25 to 1.3 times in comparison of A0 and A6 samples. Based on this work, a good correlation has emerged among the load applied, the sliding speed and its distance employed and the type and content of reinforcement adopted in the aluminum matrix.

Study on the friction drilling behaviors and tribological properties of aluminum matrix composites

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Dry sliding friction and wear properties of B4C particulate-reinforced Al-5083 matrix composites

Investigation of Mechanical and Tribological Properties of Al6061–TiB2 Metal Matrix Composites

High Temperature Mechanical Properties and Wear Performance of B4C/Al7075 Metal Matrix Composites

Tribological and Structural Effects of Titanium Carbide and Hexagonal Boron Nitride Reinforcement on Aluminum Matrix Hybrid Composites

Processing and Evaluation of Mechanical Properties and Dry Sliding Wear Behavior of AA6061-B4C Composites

Influence of the Reinforcement Phase Composition on the Structure and Abrasive Wear Resistance of Aluminum Matrix Composites Reinforced with B4C and SiC

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Mechanical and tribological characteristics of boron carbide reinforcement of AA6061 matrix composite

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Investigation of Drilling Performances, Tribological and Mechanical Behaviors of GFRC Filled with B4C and Gr

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Addition of Beryl Content to Aluminum 2024 Alloy Influencing the Slide Wear and Friction Characteristics

Investigation of wear and transverse rupture strength of AA2219/ZrO2/B4C hybrid composite materials prepared with 3D ball mixer and produced by spark plasma sintering

Wear and friction behaviour of Cu-Gr-B4C composites and correlating to the topographical characteristics

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Examination of the effect of B4C and GNP reinforcements on machinability in the machining of Al 6061 matrix B4C/GNP reinforced hybrid composites

Mechanical and tribological behaviour of tungsten carbide reinforced aluminum LM4 matrix composites

Modeling of wear performance and surface roughness of AA6061-T6/B4C composite under dry sliding conditions by RSM