Abstract:The present investigation highlights the development of high-performance materials in the construction materials industry, with a special focus on the production of aluminium matrix composites (AMCs) containing titanium carbide (TiC) particles. The stir casting method with ultrasonic assistance was employed to enhance the mechanical and tribological properties. ASTM standards were employed to evaluate the influence of TiC particles on density, hardness (VHN), ultimate tensile strength (UTS), and wear resistance at various TiC weight fraction percentages (0.0 wt.%, 2.0 wt.%, 4.0 wt.%, 6.0 wt.%, and 8.0 wt.%). Field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis were performed to analyse the microstructural changes and elemental phases present in the synthesised composite. Results revealed that the incorporation of 8 wt.% TiC reinforcement in the metal matrix composites demonstrated significant improvements compared to the base alloy. In particular, a substantial enhancement in hardness by 32%, a notable increase of 68% in UTS, and a significant 80% rise in yield strength were observed when contrasted with the pure aluminium alloy. The tensile fracture analysis of the specimens revealed the presence of dimples, voids, and cracks, suggesting a brittle nature. To assess the wear characteristics of the composites, dry sliding wear experiments were performed using a pin-on-disc wear tester. Incorporation of TiC particles resulted in a lower coefficient of friction than the base alloy, with the lowest friction coefficient being recorded at 0.266 for 6 wt.% TiC, according to the data. FESEM and energy-dispersive X-ray spectroscopy (EDXS) were used to examine the surfaces of the worn pin. Overall, the inclusion of TiC reinforcement particles in the matrix alloy greatly enhanced the wear resistance and friction coefficient of the Al-6TiC composites. Ploughing and adhesion under lower loads and delamination under higher loads were the wear mechanisms observed in the wear test.

Mechanical and tribological behaviour of tungsten carbide reinforced aluminum LM4 matrix composites

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Effect of Percentage Variation on Wear Behaviour of Tungsten Carbide and Cobalt Reinforced Al7075 Matrix Composites Synthesized by Melt Stirring Method

Tribological characteristics of AA8090-WC-ZrC metal matrix composites prepared by stir casting process for Aerospace applications

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Investigation on the mechanical and tribological behavior of tungsten-reinforced Ti-5Al-2.5Sn composites

Mechanical and Tribological Behavior of Mg-Matrix Composites Manufactured by Stir Casting

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Microstructural Characterization, Mechanical And Wear Behaviour Of Al2024-B4C Composites For Aerospace Applications

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Analysis on Mechanical Behaviour of Binary and Hybrid Al2014 Metal Matrix Composites

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Wear rate optimization of tungsten carbide (WC) nano particles reinforced aluminum LM4 alloy composites using Taguchi techniques

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Tungsten carbide particulate reinforced AA7050 aluminum alloy composites fabricated by liquid state processing

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Development and Tribological Investigation of B4C Reinforced AA5082 Aluminum Alloy Cast Composites for Automotive Applications