Abstract:GEN3 steels are a new family of automotive sheet steels developed and commercialized in the last three years, specifically for body-in-white applications. The high ductility in GEN3 steels is typically achieved through the transformation-induced plasticity (TRIP) effect by the addition of silicon or aluminum. When these steels are formed into parts, the TRIP effect of austenite to martensite transformation provides enhanced ductility. Typically, 10 to 12 micrometers of zinc coating (known as galvanized coating) is applied to automotive steel sheets for corrosion protection. Liquid metal embrittlement (LME) cracking can occur during resistance spot welding (RSW) of galvanized steels. LME cracking occurs when molten zinc penetrates prior austenite grain boundaries of the steel substrate. The precise role of silicon in the LME cracking behavior in TRIP and GEN3 steels is unknown. Therefore, a study was undertaken to examine the role of silicon in LME cracking behavior of GEN3 steels. The purpose was also to examine if the presence of retained austenite is required for LME cracking to occur. In this study, laboratory heats were prepared using three silicon levels. Samples cut from galvanized panels were welded using a resistance spot welding machine, and weld areas were examined metallographically for the presence of LME cracks. Gleeble® simulations were done to study the LME behavior of the three steels prepared. Base materials were examined with a scanning electron microscope using the electron back-scattered diffraction (EBSD) method to examine the nature of grain boundaries found. The effect of retained austenite in LME cracking was studied using the Gleeble®. Both RSW and Gleeble® results showed silicon promotes LME cracking in steels, predominantly in the weld heat-affected zones(HAZs). More low-energy, low-coincidence site lattice (CSL) boundaries were found as the silicon content of the steel was decreased. These boundaries do not host cracks. Higher silicon appeared to shrink the safe temperature range over which LME cracks could be avoided, thus indicating heat in-put control to limit cracks has limited windows as the silicon in steel goes up. It was shown that the presence of retained austenite in steel is not a prerequisite for LME cracking to occur.

Liquid Metal Embrittlement Susceptibility of the Transformation‐Induced Plasticity Steel/Lead–Bismuth Eutectic System

Liquid metal embrittlement of 12Cr ferritic/martensitic steel thin-walled tubes exposed to liquid lead-bismuth eutectic

Effect of temperature on liquid metal embrittlement susceptibility of an Fe10Cr4Al ferritic alloy in contact with stagnant lead-bismuth eutectic

Liquid metal embrittlement and deformation induced martensite: The case of 316 L austenitic steel LME by liquid eutectic gallium-indium

Liquid metal embrittlement susceptibility of an oxide-dispersion strengthened FeCrAl alloy in contact with liquid lead-bismuth eutectic at 350 °C

Liquid metal embrittlement and fracture behavior of three Mo metals in liquid lead-bismuth eutectic

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Liquid metal embrittlement of a dual-phase Al0.7CoCrFeNi high-entropy alloy exposed to oxygen-saturated lead-bismuth eutectic

Critical LME elongation: a criterion measured with Gleeble correlated to LME sensitivity during spot welding

MEASUREMENTS OF FINE STRUCTURES IN THE LEAD-BISMUTH EUTECTIC ALLOY MELTS BY DIFFERENTIAL SCANNING CALORIMETRY

A comparative study on liquid metal embrittlement susceptibility of three FeCrAl ferritic alloys in contact with liquid lead-bismuth eutectic at 350°C

Corrosion Kinetics and Mechanisms of 15-15Ti Steel in Flowing Liquid Lead-Bismuth Eutectic at 500°C

Liquid Lead–bismuth Eutectic Embrittlement Effect on the Tensile Properties of T91 Steel at 350°C

Early stages of liquid-metal embrittlement in an advanced high-strength steel

The Role of Microstructural Constituents on Strength–Ductility–Local Formability of a Transformation‐Induced‐Plasticity‐Aided Bainitic Steel

Effect of Silicon and Retained Austenite on the Liquid Metal Embrittlement Cracking Behavior of GEN3 and High-Strength Automotive Steels

Quantitative Description of External Force Induced Phase Transformation in Silicon-Manganese (Si-Mn) Transformation Induced Plasticity (TRIP) Steels

Interaction between inclusions and the TRIP effect during tensile loading of an L-PBF 18Ni-300 maraging steel and effect on ductility

Dislocation Activities at the Martensite Phase Transformation Interface in Metastable Austenitic Stainless Steel: An In-situ TEM Study

Ultrasonic cavitation erosion of 316L steel weld joint in liquid Pb-Bi eutectic alloy at 550°C

Work hardening behavior in a steel with multiple TRIP mechanisms