Abstract:Because of the wide energy gap material properties and high compatibility with existing silicon material processing, silicon carbide (SiC) has become the preferred material for power management chips that have been used in electric vehicles. On the other hand, aluminum nitride (AlN) material has become the first choice for carrying wafers due to its high strain-resistant mechanical properties, strong dielectric coefficient, excellent thermal conductivity, and high etching resistance. In this study, the surface chemistry of silicon carbide was changed into an AlN-based material to perform wafer bonding processing to develop low-temperature bonding technology for silicon carbide/aluminum nitride materials. We found through experiments that it is quite difficult for a SiC wafer to bond with an AlN wafer even if the surfaces ofthe SiC wafer and the AlN wafer are subjected to conventional surface activation treatment using oxygen plasma or argon plasma. The possible reason is that although the surface of the SiC wafer is bombarded by oxygen or argon plasmas to generate some dangling bonds, the chemical properties of Si-C and Al-N, such as electronegativity, make it difficult to generate chemical bonds between the matching surfaces of SiC/AlN. Through a material modification technology, a high-temperature sputtering method is used to make highly active AlN clusters sputtered from the target directly bond with SiC and finally form a thin AlN layer that strongly adheres to the surface of the SiC wafer. And then through the bonding of AlN/AlN homogeneous materials, although the surface roughness measurement (RMS) cannot satisfy the condition of being less than 5 angstroms for wafer bonding, the goal of low-temperature bonding can be achieved by capillary bonding. Therefore, the SiC surface is changed into an AlN-based thin layer by high-temperature sputtering, which can further chemically bond with the AlN wafer surface by capillary bonding to achieve the low-temperature bonding of SiC/AlN, as shown in Figure 1. Reference 1. Shao-Ming Nien, Jian-Long Ruan, Yang-Kuao Kuo, and Benjamin Tien-Hsi Lee, Low-temperature rough-surface wafer bonding with aluminum nitride ceramics implemented by capillary and oxidation actions, Ceramics International, Volume 48, Issue 6, 2022 Figure 1

A collective die to wafer bonding approach based on surface-activated aluminum-aluminum thermocompression bonding

Bonding of Aluminum Coated Silicon Wafers Based on Polypropylene Carbonate and As a Multi-Functional Sensor

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Wafer bonding for microsystems technologies

Mechanisms for room temperature direct wafer bonding

A novel method of anodic bonding

Heterogeneous Integration by Collective Die-To-Wafer Bonding

Low Temperature Al Based Wafer Bonding Using Sn As Intermediate Layer

Low Temperature Wafer Bonding of Silicon Carbide/Aluminum Nitride

Aluminum-coated silicon wafer bonding with tin intermediate layer

Bonding Silicon Wafers with Reactive Multilayer Foils

Time‐Dependent Surface Properties and Wafer Bonding of O 2 ‐ Plasma ‐ Treated Silicon (100) Surfaces

Ultrasonic Friction Power During Al Wire Wedge-Wedge Bonding

Effects of surface treatment on the bonding quality of wafer-level Cu-to-Cu thermo-compression bonding for 3D integration

Recent Developments in Low Temperature Wafer Level Metal Bonding for Heterogenous Integration

Enabling Ultra-Thin Die to Wafer Hybrid Bonding for Future Heterogeneous Integrated Systems

Multilayer bonding of A1N30H foils to A1050 plates using cold spot forge welding

Wafer-to-wafer bonding for microstructure formation

A Ag-Sn Isothermal Solidification Technology For Fluxless Hermetic Wafer Bonding

Bonding below 150°C Using Nano-Ag Film for Power Electronics Packaging

Wafer bonding technology and its applications in optoelectronic devices and materials