Abstract:In this study, a novel technique of consecutive multi-pass cooperative lowered-temperature rolling (CMCLR) was proposed for the first time, with the purpose of preparing high performance wrought magnesium alloys. Based on this, a highly ductile magnesium alloy sheet could be effectively produced from ingot. The corresponding microstructure could directly evolve from coarse dendrites to equiaxed grains with an average size of similar to 5 mu m, which was attributed to the intense dynamic recrystallization (DRX) during isothermal deformation. The equivalent strain gradually decreased from the surface to the interior and edge of the rolled sheet due to the anisotropic plastic deformation. Instead, the temperature of the core of the sheet was slightly higher than that of the surface due to the deformation heat effect. The basal texture in the RD-TD plane generally weakened in the form of the splitting of basal texture toward the RD and the broadening of basal plane away from the pole center due to texture randomization dominated by DRXed grains. The exceptional ductility of more than 28.7% together with acceptable ultimate tensile strength of not less than 267 MPa was ascribed to the progressive work hardening as a result of seamless switching of multiple deformation modes, i.e., basal dislocation-slip-mediated deformation was preferentially operated and then was substituted by twinning-controlled deformation and non-basal dislocation-slip-dominated deformation. The selection of {10 (1) over bar2} twin variants agreed well with geometrical compatibility factor (m') criterion instead of Schmid's law. The activated twin variants nearly engulfed the whole parent grains for the sake of preserving compatible deformation continuity at ambient temperature, giving rise to the formation of TD-split texture. Comparatively, the {10 (1) over bar2} twinning could randomize the basal texture via reorienting grain orientations which in turn facilitated the reactivation of dislocation slip systems in the case of high temperature deformation.

Improvement of stretch formability and weakening the basal texture of Mg alloy by corrugated wide limit alignment and annealing process

Enhancing Stretch Formability of Rolled Mg Sheets by Pre-Inducing Contraction Twins and Recrystallization Annealing

Tailoring the Texture and Mechanical Properties of Textured-AZ31 Mg Alloy Sheets by Twinning and Recrystallization

Effect of pre-strain levels and high temperature annealing on the formability of AZ31 Mg alloy thin sheet during stretch deformation

Improved formability of Mg-3Al-1Zn alloy by pre-stretching and annealing

Enhancement of Tensile Ductility and Stretch Formability of AZ31 Magnesium Alloy Sheet Processed by Cross-Wavy Bending

Enhanced Stretch Formability of AZ31 Magnesium Alloy Sheet by Secondary Regulation of Initial Twin Orientation

Influence of trace Ca addition on texture and stretch formability of AM50 magnesium alloy sheet

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Enhanced Stretch Formability and Mechanical Properties of a Magnesium Alloy Processed by Cold Forging and Subsequent Annealing

Effect of Pre-stretch Strain at High Temperatures on the Formability of AZ31 Magnesium Alloy Sheets

Effect of Stretch Bending on the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Influence of Warm Pre-Stretching on Microstructure and Properties of AZ31 Magnesium Alloy

Exceptional improvement in the yield strength of AZ61 magnesium alloy via cryo-stretching and its implications on the grain growth during annealing

Improving the Room-Temperature Formability of Mg-3Al-1Zn Alloy Sheet by Introducing an Orthogonal Four-Peak Texture

An Exceptional Ductility of AZ31 Magnesium Alloy Sheet Achieved by Consecutive Multi-Pass Cooperative Lowered-Temperature Rolling

Influence of Continuous Bending Process on Texture Evolution and Mechanical Properties of AZ31 Magnesium Alloy

Improved stretch formability of AZ31 sheet via texture control by introducing a continuous bending channel into equal channel angular rolling

Improving Strength and Formability of Rolled AZ31 Sheet by Two-Step Twinning Deformation

Improving the Room-Temperature Bendability of Mg-3Al-1Zn Alloy Sheet by Introducing a Bimodal Microstructure and the Texture Re-Orientation

Dramatic Improvement of Formability in Mg-3Al-1Sn-0.5Ca-0.1Sm Alloy Via Mn Microalloying Combined with High Temperature Rolling