Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

Influence of tensile twinning on electrochemical and corrosion behavior of Mg alloy

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

The influence of { 10 1 ¯ 2 } twinning on the corrosion behavior of AZ31B magnesium alloy

Effects of deformation twins on microstructure evolution, mechanical properties and corrosion behaviors in magnesium alloys - A review

Microstructure Evolution and Corrosion Performance of Az31 Magnesium Alloy Sheets

INFLUENCE OF ROLLING TEMPERATURE ON THE {1011}-{1012} TWINNING IN ROLLED AZ31 MAGNESIUM ALLOY SHEETS

Effect of Residual Tensile Stress and Crystallographic Structure on Corrosion Behavior of AZ31 Mg Alloy Rolled Sheets

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

EFFECT OF TWINNING ON MECHANICAL PROPERTY AND WORKABILITY OF Mg ALLOY

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Influence of Pre-Twinning on High Strain Rate Compressive Behavior of AZ31 Mg-alloys

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Dynamic recrystallization and twinning behavior of magnesium alloy during hot tension

Quasi-in Situ Electron Backscatter Diffraction Analysis of Twinning–detwinning Behavior in AZ31 Magnesium- Alloy Rolled Plates Subjected to Compression Loading in Different Directions

The effect of twinning and detwinning on the mechanical property of AZ31 extruded magnesium alloy during strain-path changes

Effect of Tensile Direction on Mechanical Properties and Microstructural Evolutions of Rolled Mg-Al-Zn-Sn Magnesium Alloy Sheets at Room and Elevated Temperatures

The Influence of Twinning on Plastic Constitutive Description of a Magnesium Alloy

Enhanced Stretch Formability of AZ31 Magnesium Alloy Sheet by Secondary Regulation of Initial Twin Orientation

Effects of Initial {10-12} Twins on Cyclic Deformation and Fatigue of Magnesium Alloy at Low Strain Amplitudes