Abstract:{1011}—{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy,especially at low or moderate rolling temperature.Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150℃and 300℃respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively:the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling.Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector,and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s~(-1).Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropics.The effects of the {1011} {1012} double twins occurred during rolling on the microstructure.texture and mechanical properties of the rolled sheets are discussed and related to each other.The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets,which are determined by the rolling temperature.The twins in different rolled sheets are arranged in different ways.In the normal rolled sheets,the traces of twins are approximately perpendicular to the final rolling direction,while in the cross rolled sheets there are both traces of twins parallel and to the final directions.This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction.For the same reason,the textures of twins in the rolled sheets produced through different paths are different.The textures of twins will add onto the bulks,and increases the textural difference between the bulks.The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins.

Tailoring the Texture and Mechanical Properties of Textured-AZ31 Mg Alloy Sheets by Twinning and Recrystallization

Improvement of stretch formability and weakening the basal texture of Mg alloy by corrugated wide limit alignment and annealing process

Twinning-mediated Texture Weakening in a Basal-Textured Mg-6Al-1Zn (mass%) Alloy Sheet by a Novel Cold-Sample Rolling Method

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

Twinning-Assisted Static Recrystallization and Texture Evolution in A Mg-Gd-Y-Zr Alloy

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

Tailoring the Rolling Texture of AZ31 Mg Alloy with Calcium and Tin Addition

An Exceptional Ductility of AZ31 Magnesium Alloy Sheet Achieved by Consecutive Multi-Pass Cooperative Lowered-Temperature Rolling

Texture tailoring and microstructure refinement induced by {11−21} and {10−12} twinning in an extruded Mg-Gd alloy

Twinning character and texture origination in the randomly-oriented AZ31B magnesium alloy during cold-rolling

Achieving High Ductility and Low In-Plane Anisotropy in Magnesium Alloy Through a Novel Texture Design Strategy

Unusual Twin Induced Recrystallization and Corresponding Texture Optimization in a Cold Rolled Mg-Gd-Zr Alloy During Annealing

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

Enhanced Stretch Formability of AZ31 Magnesium Alloy Sheet by Secondary Regulation of Initial Twin Orientation

Texture Weakening of AZ31 Magnesium Alloy Sheet Obtained by a Combination of Bidirectional Cyclic Bending at Low Temperature and Static Recrystallization

Effects of Zn Addition and Twin Roll Casting Process on the Microstructure, Texture, and Mechanical Properties of the Mg-Al-Mn-Ca Sheet

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

Enhancing Stretch Formability of Rolled Mg Sheets by Pre-Inducing Contraction Twins and Recrystallization Annealing

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation