Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Preparation of SiC/multilayer graphene composite ceramic with improved properties catalyzed by Ni nanoparticle

Preparation of SiC Coated Graphite Composite Powders by Nitriding Combustion Synthesis

Effects of different catalysts on performance of self-bonded SiC refractories

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

SiCn/SiC Oxidation Protective Coating for Carbon/carbon Composites

Direct chemical vapor deposition growth of graphene on Ni particles using solid carbon sources

Catalytic Nitridation Preparation of High-Performance Si3N4(w)-SiC Composite Using Fe2O3 Nano-Particle Catalyst: Experimental and DFT Studies

3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties

Synthesis of Silicon Nitride/Silicon Carbide Nanocomposite Powders through Partial Reduction of Silicon Nitride by Pyrolyzed Carbon

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Effects of in situ formed nanostructures on the structure and properties of C/SiOC composites

Catalytic and Enhanced Effects of Silicon Carbide Nanoparticles on Carbonization and Graphitization of Polyimide Films

Preparation of β-Sialon /SiC composite powder by carbothermal reaction of coal-mine schist

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Polycarbosilane as a modulator for reaction-bonded silicon carbide processing of GNPs/Si mixtures

Fabrication of Si3N4 ceramics with improved thermal conductivity by carbothermal reduction and two‐step sintering

Significant Improvement of Mechanical Properties of SiC-Nanowire-Reinforced SiCf/SiC Composites via Atomic Deposition of Ni Catalysts

Synergistic Effect of Graphene and Β-Si3n4 Whisker Enables Si3N4 Ceramic Composites to Obtain Ultra-Low Friction Coefficient

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites