Abstract:RationaleThe precision of the standard measurements of reference materials (RMs) is critical to normalize the raw δ15N values of samples to the international scale. Because the measurement configuration is required to moderate the properties of both RMs and samples for obtaining an ideal measurement precision, it is important to determine the appropriate measurement configurations of RMs to achieve accurate nitrogen isotope compositions of samples. Therefore, it is critical to systematically examine RMs for optimizing the configurations and further improve the measurement precision.MethodsGas source isotope ratio mass spectrometry (IRMS) coupled with an online elemental analyzer (EA) equipped with a single‐quartz reactor was performed to analyze the nitrogen isotope compositions. Some adjustments were made as follows: (a) as the in‐house working standard, urea was used to investigate the influences of combustion through moderating the different oxygen injections (0–20 mL) and sample delay times (10–12 s) and optimize the combustion conditions to enhance oxidation ability; (b) CO2 from the sample gas stream was removed to prevent interferences between CO2 and N2; (c) international RMs, including USGS40 (l‐glutamic), IAEA600 (caffeine), and soil standard (B2153) with a low organic content, were systematically analyzed under the optimized configurations, and the precisions of the δ15N values were further examined.ResultsOur results showed that sufficient oxygen should be injected to improve the sample combustion when analyzing δ15N in natural samples such as soil or marine sediment with low organic content. In addition, the measurement precision of δ15N was affected by the tailing of the CO2 peak from the gas chromatography column into the subsequent sample measurement if the EA is equipped with a single‐quartz reactor column. Our adjustments can produce an optimized repeatability and accuracy of the δ15N value, especially for RMs with low organic content, and the uncertainty of the measurements is improved to be better than 0.1‰ under optimized configurations.ConclusionsThe analytical conditions such as the oxygen flow rate and injection time or sample introduction time into the EA need to be adjusted depending on the combustion conditions of the RMs and samples to obtain a reliable accuracy of measurement. We recommend that when analyzing δ15N of natural samples such as soil or marine sediment samples with low organic content, more oxygen should be injected to improve the combustion of the samples. In addition, CO2 should be removed from the sample gas stream before being introduced into the isotope ratio mass spectrometer when the EA is equipped with a single‐quartz reactor.

Evaluation of 14 C/ 12 C ratio measurements using accelerator mass spectrometry with standard materials under different graphitization conditions

Performance of Home-Made Single-Stage 14C AMS System at CIAE

Small-mass Graphite Preparation for AMS 14C Measurements Performed at GIGCAS, China

Progress in AMS Measurement of U Isotope Ratios in Nanogram U Samples

AMS measurement of 53Mn and its initial application at CIAE

A HOMEMADE SEMIAUTOMATIC GRAPHITIZATION DEVICE FOR AMS 14 C DATING AT NTUAMS LAB

EXPERIMENTAL CONDITIONS FOR 14 C GRAPHITE PREPARATION AT THE GXNU LAB, CHINA

In situ carbon stable isotope measurement for graphite using LA-MC-ICP-MS

NEW SAMPLE PREPARATION LINE FOR RADIOCARBON MEASUREMENTS AT THE GXNU LABORATORY

Itemized determination of As, Sb, Bi, Se, and Ge in graphite sample by HG-AFS with high-temperature microwave digestion

Isotope ratios of total C, N, and S in particulate matter simultaneously calibrated by mixed USGS and IAEA reference materials

Establishment and Verification of a Metering Scheme for Biomass-Coal Blending Ratios Based on 14C Determination

A preliminary study of small-mass radiocarbon sample measurement at Xi'an-AMS

Development of graphitization method for low carbon aerosol filter samples with Automated Graphitization System AGE-3

Determination of concentrations of trace elements in nuclear grade graphite by charged particle activation analysis

Sample Preparation System For Carbonate And Dic In Water At The Gxnu-Ams Laboratory

Preparation and Accelerator Mass Spectrometry Determination of ~(53)Mn/~(55)Mn Standard Reference Material

Precision Dilatometer Analysis of Neutron-Irradiated Nuclear Graphite Recovery Process Up to 1673 K

Influences of Oxidation Ability on Precision in Nitrogen Isotope Measurements of Organic Reference Materials Using Elemental Analysis-Isotope Ratio Mass Spectrometry

Determination of radiocarbon content in liquid fuel blends by accelerator mass spectrometry and liquid scintillation counting in the gliwice radiocarbon and mass spectrometry laboratory

Rapid Sample Preparation of Dissolved Inorganic Carbon in Natural Waters Using A Headspace-Extraction Approach for Radiocarbon Analysis by Accelerator Mass Spectrometry