Abstract:LECO technology plays an important role for reducing the J0,metal and ρc. First, LECO paste destroys the partial passivation layer but does not corrode downward at low sintering temperature; then after LECO treatment, the glass layer was melting and continued to further corrode the ARC layer without damaging the emitter layer, forming localized corrosion pits. The contact model shows that its possible current transport mechanism is current tunneling effect through the nano‐Ag colloids in the glass layer. TOPCon solar cell with boron (B)‐doped emitters plays an important role in photovoltaic cell technology. However, a major challenge to further improving the metallization‐induced recombination and electrical contact of B‐doped emitters. Laser‐enhanced contact optimization (LECO) technology is one of ideal candidates for reducing the metallization recombination and contact resistivity. In this study, we investigate the influence of LECO technology using special Ag paste with a decreased Pb content on the performance of the metallization‐induced recombination (J0,metal), contact resistivity (ρc), microtopography of the contact, the I–V parameters, and possible conductive mechanisms. The results showed that the linear resistivity is reduced from 3.56 to 2.60 μΩ·cm owing to special Ag paste, and after LECO treatment, it also has lower ρc about 0.91 mohm·cm2. Both of them have a large contribution to the FF enhancement. Meanwhile, the J0,metal drops from 500 to 200 fA/cm2, which provides a great contribution to the improvement in open‐circuit voltage. The efficiency improved by 0.26% absolute to 25.94%, mainly because of the increased open‐circuit voltage (Voc) of 4 mV and a fill factor (FF) of 0.26%. Simulated by COMSOL, the electron concentration rises to 4 × 1019 cm−3 after LECO treatment, which can generate a larger reverse current to provide a melting temperature for the glass frit, increasing the interface glass phase conductivity. The possible current transport mechanism of LECO is current tunneling effect, resulting in the decrease in the metallization recombination. After the optimization of the LECO process with low‐corrosion paste, we manufactured industrial‐grade TOPCon cells with Eff, Voc, Jsc, and FF values as high as 26.5%, 736 mV, 42.1 mA/cm2, and 85.5%, respectively.

Nano‐size Joule‐Heating to Achieve Low‐Ohmic Ag–Si Contact on Boron Emitters of n‐TOPCon Solar Cells

Investigation of the Ag–Si contact characteristics of boron emitters for n‐TOPCon solar cells metallized by laser‐assisted current‐injection treatment

Investigation on Effects of the Laser‐Enhanced Contact Optimization Process With Ag Paste in a Boron Emitter for n‐TOPCon Solar Cell

Insight into the Contact Mechanism of Ag/Al–Si Interface for the Front‐Side Metallization of TOPCon Silicon Solar Cells

Mechanical and Electrical Properties of Ni-Ag Metallized TOPCon Silicon Solar Cells Structured by Green Picosecond Laser

Enhancing the reliability of TOPCon technology by laser-enhanced contact firing

Enhancing Adhesion and Reducing Ohmic Contact through Nickel–Silicon Alloy Seed Layer in Electroplating Ni/Cu/Ag

High-efficiency N-Topcon Cells Ensured by an Emitter Preparation Process Without Post-Oxidation

Theoretical exploration towards high-efficiency tunnel oxide passivated carrier-selective contacts (TOPCon) solar cells

Progress of plated metallization for industrial bifacial TOPCon silicon solar cells

Study on selective emitter fabrication through an innovative pre‐diffusion process for enhanced efficiency in TOPCon solar cells

Ultrafast laser-annealing of hydrogenated amorphous silicon in tunnel oxide passivated contacts for high-efficiency n-type silicon solar cells

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

Enhancing poly-Si contact through a highly conductive and ultra-thin TiN layer for high-efficiency passivating contact silicon solar cells

Advancing nickel seed layer electroplating for enhanced contact and passivation performance in TOPCon solar cells

Emitter formation with boron diffusion from PECVD deposited boron-doped silicon oxide for high-efficiency TOPCon solar cells

Regionalizing Nitrogen Doping of Polysilicon Films Enabling High‐Efficiency Tunnel Oxide Passivating Contact Silicon Solar Cells

The impact of semimetal nanoparticles on the conduction of thick glass layer at Ag/Si contact interface

Ultra-thin silicon oxide tunnel layer passivated contacts for screen-printed n-type industry solar cells

Differently shaped Ag crystallites and four current transport paths at sintered Ag/Si interface of crystalline silicon solar cells

Silicon‐based passivating contacts: The TOPCon route