Abstract:LECO technology plays an important role for reducing the J0,metal and ρc. First, LECO paste destroys the partial passivation layer but does not corrode downward at low sintering temperature; then after LECO treatment, the glass layer was melting and continued to further corrode the ARC layer without damaging the emitter layer, forming localized corrosion pits. The contact model shows that its possible current transport mechanism is current tunneling effect through the nano‐Ag colloids in the glass layer. TOPCon solar cell with boron (B)‐doped emitters plays an important role in photovoltaic cell technology. However, a major challenge to further improving the metallization‐induced recombination and electrical contact of B‐doped emitters. Laser‐enhanced contact optimization (LECO) technology is one of ideal candidates for reducing the metallization recombination and contact resistivity. In this study, we investigate the influence of LECO technology using special Ag paste with a decreased Pb content on the performance of the metallization‐induced recombination (J0,metal), contact resistivity (ρc), microtopography of the contact, the I–V parameters, and possible conductive mechanisms. The results showed that the linear resistivity is reduced from 3.56 to 2.60 μΩ·cm owing to special Ag paste, and after LECO treatment, it also has lower ρc about 0.91 mohm·cm2. Both of them have a large contribution to the FF enhancement. Meanwhile, the J0,metal drops from 500 to 200 fA/cm2, which provides a great contribution to the improvement in open‐circuit voltage. The efficiency improved by 0.26% absolute to 25.94%, mainly because of the increased open‐circuit voltage (Voc) of 4 mV and a fill factor (FF) of 0.26%. Simulated by COMSOL, the electron concentration rises to 4 × 1019 cm−3 after LECO treatment, which can generate a larger reverse current to provide a melting temperature for the glass frit, increasing the interface glass phase conductivity. The possible current transport mechanism of LECO is current tunneling effect, resulting in the decrease in the metallization recombination. After the optimization of the LECO process with low‐corrosion paste, we manufactured industrial‐grade TOPCon cells with Eff, Voc, Jsc, and FF values as high as 26.5%, 736 mV, 42.1 mA/cm2, and 85.5%, respectively.

Mechanical and Electrical Properties of Ni-Ag Metallized TOPCon Silicon Solar Cells Structured by Green Picosecond Laser

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

Progress of plated metallization for industrial bifacial TOPCon silicon solar cells

Investigation on Effects of the Laser‐Enhanced Contact Optimization Process With Ag Paste in a Boron Emitter for n‐TOPCon Solar Cell

Investigation of the Ag–Si contact characteristics of boron emitters for n‐TOPCon solar cells metallized by laser‐assisted current‐injection treatment

Enhancing Adhesion and Reducing Ohmic Contact through Nickel–Silicon Alloy Seed Layer in Electroplating Ni/Cu/Ag

Advancing nickel seed layer electroplating for enhanced contact and passivation performance in TOPCon solar cells

Enhancing the reliability of TOPCon technology by laser-enhanced contact firing

Fabrication of Metal Grid on Silicon-Based Solar Cell by Electrochemical Deposition and Microcontact Print

Direct Contact Electroplating Sequence Without Initial Seed Layer for Bifacial TOPCon Solar Cell Metallization

Enhancing poly-Si contact through a highly conductive and ultra-thin TiN layer for high-efficiency passivating contact silicon solar cells

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Effect of firing process on electrical properties and efficiency of n-TOPCon solar cells

Insight into the Contact Mechanism of Ag/Al–Si Interface for the Front‐Side Metallization of TOPCon Silicon Solar Cells

A Horizontal Double‐Sided Copper Metallization Technology Designed for Solar Cell Mass‐Production

Formation of Nanostructured Emitter for Silicon Solar Cells Using Catalytic Silver Nanoparticles

Study on the influence of micro-alkali texturing and micro-alkali polishing process on the passivation and contact performance of n-TOPCon solar cells

Performance of Large Area n-TOPCon Solar Cells with Selective Poly-Si Based Passivating Contacts Prepared by PECVD Method

Morphological, Optical and Electrical Analysis of Ag Polymer-Nickel Low Temperature Top Electrode in Silicon Solar Cell for Tandem Application

Development of TOPCon tunnel-IBC solar cells with screen-printed fire-through contacts by laser patterning

Influence of rear surface pyramid base microstructure on industrial n-TOPCon solar cell performances